manualshive.com logo in svg

Ness IDTECK iCON100, Руководство пользователя

Поделиться
Скачать
Ness IDTECK iCON100 Скачать руководство пользователя страница 12

 

 

 

101-000                                                 -12-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

 

 

Cable Range between Host & 

NESS - iCON100

 

Cable Standard 

RS-232C 

RS-422 

Standard 

1.25mm 

15m 1,200m 

UL 

0.75mm 

15m 1,000m 

UL 

0.3mm 

15m 700m 

UL 

 

Cable Range between 

NESS - iCON100

 (of V4.70 or higher) & Proximity Reader 

Cable Standard 

WIEGAND 

DATA 

POWER LINE 

Standard 

1.25mm 

150m 90m 

UL 

0.75mm 

150m 60m 

UL 

0.3mm 

100m 30m 

UL 

 

 

POWER WIRING 

Wires supplying power to 

NESS - iCON100

 may be either twisted or non-twisted pairs. Select 

the proper wire size to minimize line losses. 

 

OTHER WIRING 

Other wiring not mentioned above may be twisted or non-twisted pair wires. This would include 
wires to door contact sensors, door lock devices and other auxiliary devices. Wire runs should 
dictate the wire size used.   

 

Cable Range between 

NESS - iCON100

 & Lock, 

NESS - iCON100

 & Alarm device 

Cable Standard 

LOCK 

ALARM 

Standard 

1.25mm 

90m 90m 

UL 

0.75mm 

60m 60m 

UL 

0.3mm 

30m 30m 

UL 

CAUTION

: Install a surge absorber or reverse surge protector (diode) at any relay contact that 

switches DC voltages to an inductive load. 

 

4.1.2 TIPS FOR PLACING DEVICES 

 

NESS - iCON100

 

& READER (CARD READER) 

- Select a site to be found easily by users. 
- Prevent it from external heat. 
- Select a place safe from dirt. 
- Protect if from water or dampness. 
- Attach the unit to a plane & solid place in order it to be held strong. 
- Keep the unit a distance of more than 10cm from any metal material, monitor, motor, current 

transformer and others, otherwise they may affect the read range of the unit. 

 

Содержание IDTECK iCON100





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды