Ness IDTECK iCON100 Скачать руководство пользователя страница 49

Страница: 49 / 60

101-000 -49- Users Manual

IDTeck – iCON 1 DOOR ACCESS CONTROLLER

9.4.1 VERSION CHECK

9.4.2 SRAM TEST

9.4.3 OUTPUTS TEST

OUTPUT TEST

Relay 1 test

(Activated two times)

<ENT>

Relay 2 test

(Activated two times)

TTL Output 1 test

(Activated two times)

Output test end

Enter any key

This test is applicable to
TTL1. (0V - 5V)

This test is applicable to
TTL2. (0V - 5V)

This test is applicable to
Buzzer.

Buzzer Output test

(Activated two times)

TTL Output 2 test

(Activated two times)

This test is applicable to
Relay1 and LED.

This test is applicable to
Relay2 and LED.

RAM test pass!!!

Press any key...

Memory fail!! 00

RAM testing...

SRAM TEST

☞

. To test the SRAM memory, press the <ENT> key.

☞

. If the SRAM has problems, the LCD will show the memory block

number with a Memory Fail message. In this case, you have to
contact technical support. Press any key to return to the setup
menu.

☞

. If the SRAM is working properly then the LCD will show a

RAM test pass message. Press any key to return to the setup
menu.

VERSION

iCON100:V4.0

☞

. The version of the controller’s firmware is displayed on the LCD.
Press the <4> or <6> key to look for other menus of setup menu

Содержание IDTECK iCON100





























































Результаты поиска

Содержание IDTECK iCON100

Отзывы:

Бренды по названию

Популярные бренды

Ness IDTECK iCON100, Руководство пользователя

Результаты поиска

Содержание IDTECK iCON100

Отзывы:

Бренды по названию

Популярные бренды