Ness IDTECK iCON100 Скачать руководство пользователя страница 33

Страница: 33 / 60

101-000 -33- Users Manual

IDTeck – iCON 1 DOOR ACCESS CONTROLLER

9.1.1 READER #1 MODE SETTING

9.1.2 READER #2 MODE SETTING

READER 2 MODE

RF+PASSWORD

RF Only (default)

<ENT>

key<4> or <6>

READER 1 MODE

RF ONLY

READER 1 MODE

-> RF ONLY

☞

. It shows READER 1 MODE is set to RF ONLY operating mode.

If you want to change the mode to RF+PASSWORD operating
mode, then press the <ENT> key.

READER 1 MODE
-> RF+PASSWORD

☞

. Now you can change the mode by pressing the <4> or <6> keys.

If you want to setup the mode displayed then press the <ENT>
key to accept this mode.

Note:

RF ONLY: The door is accessible with the proximity card alone.
RF+PASSWORD: The door is accessible with the proximity card

and Password.

READER 2 MODE

RF ONLY

READER 2 MODE

-> RF ONLY

☞

. It shows READER 2 MODE is set to RF ONLY operating mode.

If you want to change the mode to RF+PASSWORD operating
mode, then press <ENT> key.

READER 2 MODE
-> RF+PASSWORD

☞

. Now you can change the mode by pressing <4> or <6> keys. If

you want to setup the mode displayed then press the <ENT> key
to accept this mode.

Note:

RF ONLY: The door is accessible with the proximity card alone.
RF+PASSWORD: The door is accessible with the proximity card

and Password.

Содержание IDTECK iCON100





























































Результаты поиска

Содержание IDTECK iCON100

Отзывы:

Бренды по названию

Популярные бренды

Ness IDTECK iCON100, Руководство пользователя

Результаты поиска

Содержание IDTECK iCON100

Отзывы:

Бренды по названию

Популярные бренды