manualshive.com logo in svg

Ness IDTECK iCON100, Руководство пользователя

Поделиться
Скачать
Ness IDTECK iCON100 Скачать руководство пользователя страница 53

 

 

 

101-000                                                 -53-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

 

B. TROUBLE SHOOTING 

 

☞ 

Broken or abnormal letters show on the LCD, when powered on.

 

Cause 

SRAM backup battery problem or LCD module problem

. 

Solution 

1. Initialize the controller   

- When power is on, turn the #8 DIPswitch from off to on.   
- Check if the LCD shows message of “Turn OFF DIP.8” “Press Any Key…” 

- Put back the DIPswitch 8 from ON to OFF.   
- Reset the power (turn off and on).   

    * Be aware that all the setting value will be put back to the default value and the data 

memory be cleared.   

    (ID data clear/Event data clear/ Time Schedule data clear etc.) 

2. Setup the date and time on SETUP MENU F1->SYS INITIALIZE and SETUP MENU F1-

>TIME SETTING.

 

3. If you still have problem, please contact a designated service center.

 

 

☞

 Randomly changed values of in/out define from previously setting value after power reset.

 

Cause

 

Discharge of RAM Back-Up battery problem during the main power off. 

Solution

 

1. Check if the Back-Up Battery Jumper is shorted.   
2. Check if the voltage of Back-Up Battery is over 3.6V.   
3. If it is over 3.6V, make initialization process as below.   

- In power-on, put off ->on the #8 DIPswitch.   
- Check if the LCD shows message of “Turn OFF DIP.8” “Press Any Key…” 

- Put back DIPswitch 8 from ON to OFF.   
- Make power reset (off and on).   

  * Aware that all the setting value will be put back to the default value and the data 

memory be cleared.   

    (ID data clear/Event data clear/ Time Schedule data clear etc.) 

4. Define IN/OUTPUT value as intend and keep the main power on more than 5 days.   
5. If after all the above, the problem remains, please contact a designated service center. 

 

 

 

 

 

Содержание IDTECK iCON100





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды