NEC V850E/MS1 UPD703100 Скачать руководство пользователя страница 337

Страница: 337 / 449

CHAPTER 11 A/D CONVERTER

User’s Manual U12688EJ4V0UM00

337

11.6.2 Scan mode operations

The analog inputs specified by the ADM0 register are selected sequentially from the ANI0 pin and A/D converted

for the specified number of times using the match interrupt signal as a trigger.

In the conversion operation, first the analog input lower channels (ANI0 to ANI3) are A/D converted for the

specified number of times. In the ADM0 register, if the lower channels (ANI0 to ANI3) of the analog input are set so

that they are scanned, and when the set number of A/D conversions ends, the INTAD interrupt is generated and A/D

conversion ends.

When the higher channels (ANI4 to ANI7) of the analog input are set so that they are scanned in the ADM0

remaining A/D conversions are executed.

The conversion results are stored in the ADCRn register corresponding to the analog input. When the conversion

of all the specified analog inputs has ended, the INTAD interrupt is generated and A/D conversion terminates (n = 0 to

7).

There are two scan modes, 1-trigger mode and 4-trigger mode, according to the number of triggers.

This is most appropriate for applications that are constantly monitoring multiple analog inputs.

(1) 1-trigger mode (Timer trigger scan: 1-trigger)

The analog inputs are A/D converted for the specified number of times using the match interrupt signal

(INTCC110) as a trigger.

The analog input and ADCRn register correspond one to one.

When all the A/D conversions specified have ended, the INTAD interrupt is generated and A/D conversion

ends.

Trigger

Analog Input

A/D Conversion Result Register

INTCC110 interrupt

ANI0

ADCR0

INTCC110 interrupt

ANI1

ADCR1

INTCC110 interrupt

ANI2

ADCR2

INTCC110 interrupt

ANI3

ADCR3

ANI4

ADCR4

ANI5

ADCR5

ANI6

ADCR6

(A/D trigger mode)

ANI7

ADCR7

When the match interrupt is generated after all the specified A/D conversions end, A/D conversion is restarted.

When the TM11 is set to the 1-shot mode, and less than a specified number of match interrupts are generated,

if the CE bit is set to 0, the INTAD interrupt is not generated and the standby state is set.

Содержание V850E/MS1 UPD703100


































































































































































































































































































































































































































































Результаты поиска

Содержание V850E/MS1 UPD703100

Отзывы:

Похожие инструкции для V850E/MS1 UPD703100

Бренды по названию

Популярные бренды

NEC V850E/MS1 UPD703100, Руководство пользователя

Результаты поиска

Содержание V850E/MS1 UPD703100

Отзывы:

Похожие инструкции для V850E/MS1 UPD703100

Бренды по названию

Популярные бренды