NEC V850E/MS1 UPD703100 Скачать руководство пользователя страница 329

Страница: 329 / 449

CHAPTER 11 A/D CONVERTER

User’s Manual U12688EJ4V0UM00

329

11.5 Operation in A/D Trigger Mode

When the CE bit of the ADM0 register is set to 1, A/D conversion starts.

11.5.1 Select mode operations

The analog input specified by the ADM0 register is A/D converted. The conversion results are stored in the

ADCRn register corresponding to the analog input. For the select mode, the 1-buffer mode and 4-buffer mode are

supported according to the storing method of the A/D conversion results (n = 0 to 7).

(1) 1-buffer mode (A/D trigger select: 1-buffer)

One analog input is A/D converted once. The conversion results are stored in one ADCRn register. The

analog input and ADCRn register correspond one to one.

Each time an A/D conversion is executed, an INTAD interrupt is generated and the AD conversion terminates.

Analog Input

A/D Conversion Results Register

ANIn

ADCRn

(n = 0 to 7)

If 1 is written to the CE bit of the ADM0 register, A/D conversion can be restarted. This is most appropriate for

applications in which the results of each first time A/D conversion are read.

Figure 11-6. Example of 1-Buffer Mode (A/D Trigger Select 1-Buffer) Operation

ANI0

ANI1

ANI2

ANI3

ANI4

ANI5

ANI6

ANI7

ADCR0

ADCR1

ADCR2

ADCR3

ADCR4

ADCR5

ADCR6

ADCR7

A/D converter

ADM0

(1)

CE bit of ADM0 is set to 1 (enable)

(2)

ANI2 A/D conversion

(3)

Conversion result is stored in ADCR2

(4)

INTAD interrupt generation

Содержание V850E/MS1 UPD703100


































































































































































































































































































































































































































































Результаты поиска

Содержание V850E/MS1 UPD703100

Отзывы:

Похожие инструкции для V850E/MS1 UPD703100

Бренды по названию

Популярные бренды

NEC V850E/MS1 UPD703100, Руководство пользователя

Результаты поиска

Содержание V850E/MS1 UPD703100

Отзывы:

Похожие инструкции для V850E/MS1 UPD703100

Бренды по названию

Популярные бренды