NEC UX5000 Скачать руководство пользователя страница 245 | Manualshive

Страница: 245 / 334

background image

Chapter 4 - Terminals and Optional Equipment

Chapter 4

4 - 51

4.14.7

GBA Adapters

- P/N

0912042

The GBA Adapter provides an IP-CTS or IP Enhanced terminal with a gigabit ethernet connection. The adapter
provides a 10/100Mbps connection to the IP terminal and a gigbit connection to a PC. The adapter requires
local power from an AC-L power adapter or PoE (subject to the terminal’s power requirements).

When installing or removing the adapters,

the keyset should first be unplugged from the system

. Terminals

with an adapter installed can be wall-mounted, however, a separate wall-mount bracket must be used (P/N
680610).

4.14.7.1 LED Indications

For specifications, refer to

UX5000 SYSTEM SPECIFICATIONS

(page 6-1).

Option Compatibility

IP Terminal

Digital Keyset

IP-CTS

Enhanced

Value

Enhanced

Value

✔

✔

NA

NA

NA

Feature

Comments

Static LAN Speed
Configuration

Only Auto negotiation is supported. Fixed speed
and fixed duplex are not support.

PC Port VLAN

Though the PC port of the IP terminal supports
VLAN, the Gigabit Ethernet adapter does not.
This means that VLAN tag add/remove and
filtering by VLAN ID are not supported.

PC Port Shutdown

There is no ability to reject improper access to the
PC port.
It is recommended that if the PC port is not used
that the IP terminal not use the GBA adapter, but
should be connected directly to the LAN switch.

Tag VLAN for
Terminal Function
(SIP and RPT, etc.)

Tagged VLAN for the IP terminal is supported as
the tagged packets will be forwarded correctly.

LED

1000Mbps is

Connected

100Mbps is

Connected

10Mbps is

Connects

Speed

Display

Green

Red

Off

LED

LINK

ACT

LINK / ACT Display

Green

Blinking Green

«
...
243
244
245
246
247
...
»

Содержание UX5000















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UX5000

Бренд: NEC Страницы: 6

Univerge SV9100

Бренд: NEC Страницы: 8

Univerge SV9100

Бренд: NEC Страницы: 4

Univerge SV9100

Бренд: NEC Страницы: 9

Univerge SV9100

Бренд: NEC Страницы: 36

UNIVERGE SL2100

Бренд: NEC Страницы: 4

Univerge SV9100

Бренд: NEC Страницы: 5

UNIVERGE SL2100

Бренд: NEC Страницы: 11

Бренд: NEC Страницы: 256

Бренд: NEC Страницы: 30

Бренд: NEC Страницы: 5

Univerge SV9100

Бренд: NEC Страницы: 3

Univerge SV9100

Бренд: NEC Страницы: 4

UNIVERGE UM8700

Бренд: NEC Страницы: 2

Бренд: Yealink Страницы: 2

KX-TG2267B - GigaRange - 2.4 GHz Digital Cordless...

Бренд: Panasonic Страницы: 72

Бренд: Chamberlain Страницы: 4

Бренд: Topcom Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды