manualshive.com logo in svg

NEC UX5000, Руководство по оборудованию, Страница: 111 / 334

Поделиться
Скачать
NEC UX5000 Скачать руководство пользователя страница 111

Chapter 2 - Blade Installation and Startup

Chapter 2

2 - 25

2.4.2.2

Removing the EXIFU Cover (Figure 2-8)

1.

Press on the right-hand side of the EXIFU cover and pull the cover open. Slide the cover
slightly to the left to unhook the 3 hooks which hold on the cover.

2.4.2.3

To install an EXIFU blade:

1.

Remove the EXIFU cover as described previously from each of the chassis.

2.

Carefully remove the blank filler piece on the cover to allow for the EXIFU connectors.

3.

For the Controlling Chassis-B1 (with the CCPU), install the EXIFU-B1 into the slot.

4.

For the Base Chassis-B1(s), install the EXIFU-E1 into the slot in each of the additional
chassis. Screw the blade to the chassis using the screw provided.

Figure 2-8:    REMOVING THE EXIFU COVER

Hooks

This cover has three Hooks

at the left hand side.

Press here to pull
the cover.

•

Do not remove or install this blade with the power on

.

Содержание UX5000















































































































































































































































































































































Отзывы:

Нет отзывов