manualshive.com logo in svg

NEC UX5000, Руководство по оборудованию, Страница: 281 / 334

Поделиться
Скачать
NEC UX5000 Скачать руководство пользователя страница 281

Chapter 5

5 - 1

Chapter 5 - LAN Connection

Chapter  5 -

LAN Connection

S

ECTION

 5-1

LAN DEVICES

5.1.1

Using LANs

Using a LAN setup (local area network) with the UX5000 system complies with the ethernet standard (10Base-
T/100Base-TX).

To connect a telephone to a LAN connection, the system allows the use of a UX5000 digital IP keyset or an 
H.323 IP digital telephone.

If connecting a LAN to a WAN (wide area network), follow the instructions included with the ADSL modem or 
gateway device.

5.1.2

IP Address

Equipment/devices used in the UX5000 LAN setup must have an IP address assignment. An IP address 
assigns a unique address for each device. There are two types of IP addresses: Private and Global. A Private 
IP Address is not accessible through the internet - a Global IP Address can be accessed through the internet.

With a Private IP Address, with equipment that does not access the internet directly, addresses can be 
assigned to the equipment within Class A, B or C by assigning a number within the class’s range of numbers.

Class

Allowed IP Address

Recommended 

Environment

A

10.0.0.0  ---10.22.255.255

Large Scale Network

B

172.16.0.0 --- 172.31.255.255

Mid Scale Network

C

192.168.0.0 --- 192.168.255.255

Small Scale Network

Содержание UX5000















































































































































































































































































































































Отзывы:

Нет отзывов