manualshive.com logo in svg

NEC UX5000, Руководство по оборудованию, Страница: 227 / 334

Поделиться
Скачать
NEC UX5000 Скачать руководство пользователя страница 227

Chapter 4 - Terminals and Optional Equipment

Chapter 4

4 - 33

S

ECTION

 4-11

HEADSETS

4.11.1

Connecting a Headset (Figure 4-17)

A keyset user can utilize a customer-provided headset in place of the handset. Like using Handsfree, using the 
headset frees up the user’s hands for other work. However, Headset Operation provides privacy not available 
from handsfree.

The headset plugs into a separate jack on the bottom of the terminal. This allows the use of the handset or 
headset - whichever is convenient at the time.

Simply connect the headset into the headset jack located on the bottom of the terminal. (This jack is located 
near the handset jack, so make sure to connect to the proper jack.) The headset jack is pre-amplified and the 
addition of an after-market amplification device can result in poor audio performace.

Examples of compatible headsets are:

Plantronics Polaris Headsets:
  Polaris SupraPlus/NC-M (monaural with noise canceling transmitter)
  Polaris SupraPlus/NC-B (binaural with noise canceling transmitter)
  Polaris SupraPlus/VT-M (monaural with voice tube transmitter)
  Polaris Encore/VT-M (monaural with voice tube transmitter)
  Polaris Encore/NC-B (binaural with noise canceling transmitter)
  Polaris Tristar/VT-M (monaural with noise canceling transmitter)
  Polaris Mirage/VT-M (monaural with voice tube transmitter)

Part Number

750643
750645
750644
750634
750635
750630
750631

Figure 4-17:   HEADSET CONNECTION

Содержание UX5000















































































































































































































































































































































Отзывы:

Нет отзывов