NEC UX5000 Скачать руководство пользователя страница 87

Страница: 87 / 334

Chapter 2

2 - 1

Chapter 2 - Blade Installation and Startup

Chapter 2 - Blade Installation

and Startup

ECTION

2-1

BLADE LAYOUT

2.1.1

Blade Location

Determine the slot position for each blade. In the Controlling chassis:

●

Slot 1 - dedicated for the CCPU

●

EXIFU slot - dedicated for the Expansion blade

In the Expansion Chassis:

●

EXIFU slot - dedicated for the Expansion blade

The Controlling/Base and Expansion Chassis:

●

Slots 2-16 are universal (any type of blade can be installed)

Important Notes

•

Make sure to follow the steps indicated in

Powering Up the System/Initial Blade

Installation

(page 2-87) for an initial system install. This will ensure that you start the

system with the default system settings.

•

To delete a blade from the system,

the blade must first be removed from the system

chassis

, then Program 90-05-01 can be used to delete the slot definition.

Содержание UX5000















































































































































































































































































































































Результаты поиска

Содержание UX5000

Отзывы:

NEC UX5000, Руководство по оборудованию, Страница: 87 / 334

Результаты поиска

Содержание UX5000

Отзывы: