NEC UX5000 Скачать руководство пользователя страница 263 | Manualshive

Страница: 263 / 334

NEC UX5000 Скачать руководство пользователя страница 263

Chapter 4 - Terminals and Optional Equipment

Chapter 4

4 - 69

4.17.3

Programming the IP Terminal for the 911 Dialing When Lock Feature Activated

The Lock button on the IP terminals will provide a user with the ability to prevent calls on their terminal while
away from their desk. This will prevent all calls from being dialed - including 911. In order to allow anyone to
dial 911 from a locked IP terminal, each terminal must be set up to override the lock function. Each IP terminal
can have up to 3 emergency numbers defined which can be dialed when a terminal is locked. Perform the
following steps on any IP terminal which may be used to dial an emergency number.

1.

Enter the terminal’s program mode by pressing HOLD CONF * #.

2.

At the log-in screen, enter the user name (default: ADMIN) and password (default: 6633222) and press
the OK Soft Key.

3.

Press Soft Key 6 for “Application Setting”.

4.

Press Soft Key 5 for “Emergency Call”.

5.

Press Soft Key 1, 2 or 3 for the emergency number entry.

6.

Dial the emergency number to be allowed (ex: 911).

7.

Press Soft Key 4 for “OK” to complete.

8.

Continue pressing Soft Key 4 to exit (Exit-Exit-Save). The terminal will reset automatically.

4.17.4

Using the Lock Feature on IP-CTS or Enhanced Terminals

The Lock button on the IP-CTS or IP Enhanced terminals will provide a user with the ability to prevent calls on
their terminal while away from their desk. This will prevent all calls from being dialed - including 911 (unless
allowed by changing the terminal’s setup (as defined above).

1.

Press the LOCK button at the top of the IP-CTS or IP Enhanced terminal.

2.

The screen displays “Security Lock?”. Press the OK Soft Key to enable or CANCEL to exit without setting
the feature.

●

The screen displays a screen saving while locked and the Lock LED will be lit.

3.

To clear the Lock feature, press any key. The screen request the password entry. Dial the 4-digit
password for the terminal and press the OK Soft Key.

●

The terminal returns to an idle condition. If required, the UX5000 administrator can reset
the terminal if a password is forgotten.

! Important !

Once a locked terminal is used to dial an emergency number, the terminal will be
unlocked until the Lock button is pressed again.

«
...
261
262
263
264
265
...
»

Содержание UX5000















































































































































































































































































































































Отзывы:

Нет отзывов