NEC SL1100, Руководство по функциям и спецификациям

Страница: 696 / 864

Program Num-
ber
Program Name Default
10-12-10 CPU Network Setup - Subnet Mask
Assign the subnet mask for the VoIPDB card.
Refer to the programming manual for
all the possible valid subnet mask en-
tries.
(default)
255.255.0.0
10-19-01 VoIPDB DSP Resource Selection
This program is used to assign the 16 or 32 resources of the
VoIPDB.
NEC recommends leaving the default settings as system de-
fault.
0 = Commonly used for IP extensions,
trunks, and networking
1 = Use for IP extensions
2 = Use for SIP trunks
3 = Use for networking (SL Net)
5 = Blocked
6 = Common without unicast paging
7 = Multicast paging
8 = Unicast paging
(defaults)
Resource 1 = 1
Resource 2 ~ 32 = 0
10-20-01 LAN Setup for External Equipment - TCP Port
Device type 4 (networking system) must be assigned to the
same port number in
ALL SL Net systems.
1 = CTI Server (default = 0)
4 = Networking System (default =
30000)
5 = SMDR Output (default = 0)
6 = DIM Output (default = 0)
9 = 1st Party CTI (default = 0)
11 = OM Server (default = 8010)
12 = Traffic Report Output (default = 0)
13 = Room Data Output for Hotel
Service (default = 0)
Available values are: 0 ~ 65535
10-27-01 IP System ID - IP Address
Define the IP Address of the Remote SL Net system where the
call is routed for the system ID assigned in PRG 11-01-01.
0.0.0.0 ~ 126.255.255.254
128.0.0.1 ~192.255.255.254
192.0.0.1 ~ 223.255.255.254
(default)
0.0.0.0
11-01-01
*1
System Numbering
Assign the leading digit/digits of the remote SL Net systems
as: (8) Networked System Access.
Example 1: The Remote SL Net system is going to use exten-
sions 200 ~ 299 then the digit 2 would be assigned as: (8) Net-
worked System Access.
Example 2: The Remote SL Net system is going to use exten-
sions 1200 ~ 1299 then the digits 12 would be assigned as: (8)
Networked System Access.
0 = Not Used
1 = Service Code
2 = Extension Number
3 = Trunk Access Code
4 = Individual Trunk Access Code
5 = Operator Access
6 = F-Route
8 = Networked System Access
9 = Dial Extension Analyze
Refer to Programming Manual.
11-01-01
*1 System Numbering
Once the leading digits/digits are assigned as network access,
you must then assign them to a valid Network ID (1 ~ 4).
The 1
st
remote system would be network ID 1, the second
would be network ID 2, the 3
rd
would be network ID 3, and
the 4
th
would be network ID 4. The network ID's at each re-
mote location do not have to match; they are system depend-
ant.
For example, if the Remote SL Net system uses extensions
200 ~ 299, then digit 2 would be assigned as: (8) Networked
System Access and digit 2 would be assigned as network ID 1.
0 = No Remote Network
1 = Remote Network 1
2 = Remote Network 2
3 = Remote Network 3
4 = Remote Network 4
(default)
0
20-01-04 Network BLF Indication
Assign how often the SL1100 updates the DSS key BLF indi-
cations for remote SL Net systems (expressed in seconds).
To provide BLF lamping indications across the network, this
timer must be adjusted. NEC recommends a value of 3 sec-
onds.
0 ~ 64800 seconds
(default)
0
SL1100 ISSUE 2.0
1-684 SL Net
S