NEC SL1100 Скачать руководство пользователя страница 454 | Manualshive

Страница: 454 / 864

NEC SL1100 Скачать руководство пользователя страница 454

• The VoIPDB uses two addresses, one address is for signaling and the other address for voice

traffic.

• An on-board RJ-45 connector provides a WAN/LAN connection. Voice and signaling data to/from

the IP Stations are converted into IP Frames and transmitted through the Data Communication IP
Network.

• The VoIPDB supports a maximum of 32 VoIPDB connections.
• Duplex mode (Auto or Full) and speed (10 or 100 mbps) are configured via SL1100 unit

programming.

In voice communication, particularly Internet telephony, the

M

ean

O

pinion

S

core (MOS) provides a

numerical measure of the quality of human speech at the circuit destination. The scheme uses
subjective tests (opinionated scores) that are mathematically averaged to obtain a quantitative
indicator of the system performance. The maximum MOS is 5.0.

• SL1100 supports a 100 rel option and Session Timer option.
• SL1100 supports Early Media.
• SL1100 SIP restricts an outgoing call under the following conditions:

- SIP configuration failed
- SIP registration failed
- Lack of VoIPDB resource
- Lack of a VoIPDB bandwidth

• Both port numbers can be configured by system data.
• ToS Support.

Conditions

• Documentation for Polycom devices are available at

http://www.polycom.com/voicedocumentation

.

• Quick User Guides for supported Polycom devices are available at

http://www.necntac.com

under

Technical Documentation/Telephony/Polycom Soundstation

(valid Username and Password

required).

• SIP Stations which support RFC 3842 (Message Waiting) receive Message Waiting Lamp

indications.

• SIP Station - VoIPDB does not support NAT traversal.
• SIP Station - VoIPDB does not support a Blind Transfer feature.
• Supports video codecs H.264, H.263, and H.261.
• Video is supported when P2P for standard SIP is turned on. (PRG 10-26-03 SIP Peer-to-Peer Mode

ON)

• Auto start video when call is answered is not supported.
• SIP Station and SIP Trunk require a license key for activation. Once activated, the SIP Client

license may be shared between SIP Station and SIP Trunks.

• SIP protocol (RFC3261) is used.
• SIP Station uses the VoIPDB as a media gateway.
• Default UDP listen port for a SIP station is 5070. Both port numbers can be configured by system

data.

• SL1100 Station registration policy supports an authentication feature. Enabling this policy prevents

the registered telephone from unexpected override.

• SL1100 supports HOLD and TRF feature on the basis of IETF draft.

- draft-ietf-sipping-service-examples-09.txt
- Section 2.5 (Transfer - Attended) of draft-ietf-sipping-service-examples-15.txt
- draft-ietf-sip-session-timer-10.txt

• When all VoIPDB DSP resources are busy, the SIP Terminal cannot preempt active calls to make a

911 call.

• The SL1100 CPU is the registration server for the SIP stations. The configurable IP Address is

located in PRG 10-12-09 (SL1100 Network Setup - IP Address).

SL1100

ISSUE 2.0

1-442

IP Single Line Terminal (SIP)

I

«
...
452
453
454
455
456
...
»

Содержание SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды