NEC SL1100 Скачать руководство пользователя страница 479 | Manualshive

Страница: 479 / 864

NEC SL1100 Скачать руководство пользователя страница 479

Program

Number

Program Name/Description

Assigned Data

22-02-01 *

Incoming Call trunk Setup

Assign all PRI trunks as an incoming type of DDI Mode Switching (set-
ting data 8).
This program is per trunk and per day/night mode, which there are 8
day/night modes. It is recommended that all 8 day/night modes be set
as DDI.

0 = Normal
1 = VRS
2 = DISA
3 = DID
4 = DIL
5 = E&M Tie Line
6 = Delay VRS
7 = ANI/DNIS
8 = DID (DDI) Mode Switching
(default = 0)

14-05-01

Trunk Group Setup

Assign all PRI trunks, including the D-Channel, to a valid trunk group.
Do not assign any used PRI trunks in trunk group 0.

0 ~ 25
(default = 1)

22-09-01

Expected number of Digits

Enter the number of digits, per the trunk group assigned in PRG
14-05, that the Telco will be sending to the SL1100 as DID's.
The SL1100 will analyze the digits received from the Telco starting
from the last digits working towards the first digits.
Example:
If the SL1100 was set to receive 4 digits and the Telco sent 10 digits
(214-555-1000) the SL1100 would route off of the last 4 digits re-
ceived (1000).

1 ~ 8
(default = 4)

22-17-01 *

DDI Translation Table

Enter the digits received from the Telco that are going to be transla-
ted.
The amount of digits entered should be equal to the setting assigned
in PRG 22-09-01.

Maximum of 8 digits

(0 ~ 9,

*

, #)

500 tables (entries) max

(default = Not Assigned)

22-17-04 *

Dial In Conversion table Number

Used to assign a DID translation table to one of the 500 entries in
PRG 22-17-01 per day night mode.
This can be done automatically following the system day/night modes
or manually via a function key.

1 ~ 800

(These are the table entries

in PRG 22-11.)

(default = Not Assigned)

22-11-01

Received Number
DO NOT

assign anything here for the tables specified in PRG

22-17-04.
This must be left blank or the DDI routing will not work.

Maximum of 8 digits

(0 ~ 9,

*

, #)

(default = Not Assigned)

22-11-02 *

Target Number

Enter the destination number to which the DID is to be sent.

Maximum of 8 digits

(0 ~ 9,

*

, #, @)

(default = Not Assigned)

20-09-02 *

Caller ID Display

Per class of service this allows or denies the stations from receiving
the caller ID name/number that the Telco is sending in.

0 = OFF

(Caller ID NOT displayed.)

1 = ON

(Caller ID is displayed.)

(default = 0)

20-07-26 *

Dial In Mode Switch

Per class of service this allows or denies the stations ability to control
the DDI switching.

0 = OFF

(Station cannot control DDI

switching.)

1 = ON

(Station can control DDI

switching.)

(default = 0)

15-07-01 *

Programmable Function Keys

This program is used on a per station basis to assign different function
keys to the Multiline Terminals. Function key (

88

) is used to control

the night mode switching change per DID.
One key will control one specific DID. Multiple keys are needed to
control multiple DID's.

88 = Dial In Mode Switching
(Refer to the programming manual for
the default values and for all other
available options in this command.)

Operation

None

ISSUE 2.0

SL1100

Features and Specifications Manual

1-467

I

«
...
477
478
479
480
481
...
»

Содержание SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды