manualshive.com logo in svg

NEC SL1100, Руководство по функциям и спецификациям

"NEC SL1100" - бизнес-телефонная система с обширными функциями, облегчающая работу администраторов. Для получения руководства администратора можно бесплатно скачать с manualshive.com. Управляйте вашим бизнесом эффективно и легко с помощью этого надежного устройства.

Поделиться
Скачать
background image

When the capacity is exceeded, an alarm report is generated and the message "NW port limit
exceeded" is displayed on an Alarm indication telephone. To restore the network, so all systems can
communicate with each other, the system totals need to be brought below the 168 port maximum.
After the necessary ports (station or trunk) are removed from a system, a restart of the SL1100 is not
required. Every time a system in an SL Net network is reset, a port count is performed. If the network
port count is below 168, all systems are allowed to communicate.

InMail ports are not counted against the 168 port maximum capacity.

Each system will require a VoIPDB, which by default will provide 16 channels to be shared for all IP
related devices (e.g. IP Phones, IP Trunks, SL Net). If more than 16 channels are required at any site,
the system must have the following license: 

SL-IP-CHANNEL-16 LIC

 (0042). With this license

installed, the system will now have 32 channels to share for all IP devices. Every system that requires
32 ports must purchase and install this license.

Network Requirements

The voice quality of VoIP depends on variables such as available bandwidth, network latency, and
quality of service initiatives (QoS), all of which are controlled by the network and internet service
providers. Because these variables are not within NEC's control, the performance of the users IP-
based voice solution cannot be guaranteed. Therefore, NEC recommends connecting the VoIP
equipment through a fully managed data network with Quality of Service (QOS) implemented.

For a network to be suitable for VoIP it must pass specific requirements. The requirements are:

• One way delay must not exceed 150 ms
• Round trip delay must not exceed 300 ms
• Packet loss must not exceed 1 %
• Data switches must be manageable
• No half-duplex equipment may be present in the network
• Routers must provide QOS

Depending upon how the QOS policies are built in the network, assignments may be needed in the CPU
(PRG 84-10).

• Adequate bandwidth for the estimated VoIP traffic must be available

See below chart for bandwidth calculations.

Below is a chart that shows the average bandwidth per VoIP call over Ethernet.

SL1100

ISSUE 2.0

1-680

SL Net

S

Содержание SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SL1100

Caliber MCD065 Instruction Manual preview
MCD065
Бренд: Caliber Страницы: 8
Yamaha CBX-D5 Troubleshooting Manual preview
CBX-D5
Бренд: Yamaha Страницы: 4
Fractus Antennas TVNext NN01-054 User Manual preview
TVNext NN01-054
Бренд: Fractus Antennas Страницы: 14
IN-COMMAND NCSP35CM Installation And Operation Manual preview
NCSP35CM
Бренд: IN-COMMAND Страницы: 47
Jensen JDH910BT User Manual preview
JDH910BT
Бренд: Jensen Страницы: 13
N-Com BX4 PLUS User Instructions And Safety preview
BX4 PLUS
Бренд: N-Com Страницы: 32
PAC P1C-GM12 Installation Manual preview
P1C-GM12
Бренд: PAC Страницы: 12
Teac CR-K1 Service Manual preview
CR-K1
Бренд: Teac Страницы: 16
SIMARINE SC302T User Manual preview
SC302T
Бренд: SIMARINE Страницы: 22
Yealink MVC940 Quick Start Manual preview
MVC940
Бренд: Yealink Страницы: 36
AbleNet iTalk4 Quick Start Manual preview
iTalk4
Бренд: AbleNet Страницы: 8
Grundig MS 235 Manual preview
MS 235
Бренд: Grundig Страницы: 24
Panasonic RX-C52 Operating Instructions Manual preview
RX-C52
Бренд: Panasonic Страницы: 20
Toa RM-200M Manual preview
RM-200M
Бренд: Toa Страницы: 9
RCA RS2010 User Manual preview
RS2010
Бренд: RCA Страницы: 20
RCA RS2128i User Manual preview
RS2128i
Бренд: RCA Страницы: 2
Polycom SoundPoint IP 560 Configuring preview
SoundPoint IP 560
Бренд: Polycom Страницы: 9
Tridonic modularDIM BASIC Installation Instructions preview
modularDIM BASIC
Бренд: Tridonic Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды