NEC SL1100 Скачать руководство пользователя | Manualshive

Страница: 665 / 864

background image

• After finishing VRS message, destination person can start monitoring of inspection terminal. Also by

dialing

*

from outside it is possible to have a two-way conversation.

If you dial

*

while the message is being played, this will not enable the cut through. Dialing

*

during

the message stops the message from being played and you must dial

*

again to enable two-way

speech path.
When using Analog trunks, the destination person must dial

*

before the initial message is played to

the caller.

• If outgoing call restriction is set, the emergency call number must be pre-registered in the restriction

allow table, then emergency call can go through. Also even all trunk are busy, the call has high
priority and can go out.

• If destination does not answer the emergency call, the system repeatedly places the call for the

number of times specified in PRG 20-45-07.

• Maximum of 6 extensions can be set as Remote Inspection terminals.
• If all VRS channels are busy, tone will be provided instead of VRS message, such as for inspection

message or for destination message.

• If VRS message itself is not recorded, tone will be provided.

Emergency call destination MUST be set considering this feature’s purpose.

• The emergency number dialed does not follow ARS settings.

If PRG 13-01-01 is set to Trunk the system uses command PRG 13-05 to route the emergency call.
If PRG 13-01-01 is set to ICM the system uses command PRG 14-06 to route the emergency call.

• The VRS allows you to record up to 100 VRS messages (001-100) when using the compact flash

card. If you are using the built in VRS, without the compact flash, then you can only record message
1 (001).

Emergency Call 1

Emergency calls when “Security Sensor” or “Remote Inspection” performed, SMDR can record these
call class as follows.

• Security Sensor: SAD
• Remote Inspection: WAD

If the system is using the built in VRS for messages and a message is being played over the paging system
(Internal or External), then the outside emergency call will not play a message; it will play warning tone.
The built in VRS only has 1 channel and can either play the message over the paging system or play the
message to the outside caller; it cannot do both.

Emergency Call 2

Emergency calls when “Security Sensor” or “Remote Inspection” performed, alarm report can record
these alarm and alarm display terminal indicates following on LCD.

• Security Sensor: 31: Sensor Dial
• Remote Inspection: 32: Confirm dial

Recording Emergency Call

By setting PRG 90-20-11 (1; Report), Emergency calls can be recorded on security report.

• Maximum of 50 records can be saved.

Default Settings

None

ISSUE 2.0

SL1100

Features and Specifications Manual

1-653

S

«
...
663
664
665
666
667
...
»

Содержание SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SL1100

Бренд: Maco Страницы: 40

Videoconferencing system

Бренд: PictureTel Страницы: 122

Бренд: Yealink Страницы: 52

Бренд: DS Страницы: 7

Бренд: Samsung Страницы: 27

Бренд: Samsung Страницы: 23

Бренд: Samsung Страницы: 29

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 29

Бренд: Samsung Страницы: 29

Бренд: Samsung Страницы: 38

Бренд: Samsung Страницы: 62

Бренд: Samsung Страницы: 68

Бренд: Sanyo Страницы: 22

Бренд: Contacta Страницы: 12

PCS-1 - Video Conferencing Kit

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды