manualshive.com logo in svg

NEC mPD178053, Руководство пользователя

"NEC mPD178053" - микроконтроллер с пользовательским руководством. Вы можете скачать бесплатное руководство по эксплуатации на {веб-сайте}. Получите подробную информацию о продукте, чтобы легко использовать и программировать ваш микроконтроллер. Идеально подходит для профессионалов и любителей в электронике.

Поделиться
Скачать
background image

99

CHAPTER 6   8-BIT TIMER/EVENT COUNTERS 50 TO 53

User’s Manual  U15104EJ2V0UD

6.2  Configuration of 8-Bit Timer/Event Counters 50 to 53

8-bit timer/event counters 50 to 53 consist of the following hardware.

Table 6-1.  Configuration of 8-Bit Timer/Event Counters 50 to 53

Item

Configuration

Timer registers

8-bit timer counters 50, 51, 52, and 53 (TM50 to TM53)

Registers

8-bit compare registers 50, 51, 52, and 53 (CR50 to CR53)

Timer outputs

3 lines (TO50 to TO52)

Control registers

•  Timer clock select registers 50, 51, 52, and 53 (TCL50 to TCL53)

•  8-bit timer mode control registers 50, 51, 52, and 53 (TMC50 to TMC53)

(1) 8-bit timer counters 50, 51, 52, and 53 (TM50 to TM53)

TM5n is an 8-bit read-only register that counts the count pulses.

The counter is incremented at the rising edge of the count clock.

TM50 and TM51 or TM52 and TM53 can be cascaded and used as a 16-bit timer.

When TM50 and TM51 are cascaded and used as a 16-bit timer, its value can be read using a 16-bit memory

manipulation instruction.  However, because TM50 and TM51 are connected with the internal 8-bit bus, they

are read one at a time.  Therefore, read the value of TM50 and TM51 when used as a 16-bit timer two times

for comparison, taking changes in the values during counting into consideration.

When TM52 and TM53 are cascaded and used as a 16-bit timer, its value can be read using a 16-bit memory

manipulation instruction.  However, because TM52 and TM53 are connected with the internal 8-bit bus, they

are read one at a time.  Therefore, read the value of TM52 and TM53 when used as a 16-bit timer two times

for comparison, taking changes in the values during counting into consideration.

If the count value is read while the timer is operating, stop input of the count clock, and read the count value

at that point.  The count value is cleared to 00H in the following cases.

<1> RESET input

<2> Clearing TCE5n

<3> Match between TM5n and CR5n in mode in which the timer is cleared and started on match between

TM5n and CR5n

Caution

When TM50 and TM51 or TM52 and TM53 are cascaded, the value of the timer is cleared

to 00H even if the least significant bit (TCE50 or TCE52) of timer mode control register

50 (TMC50) or 52 (TMC52) is cleared.

Remark

n = 0 to 3

Содержание mPD178053
















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для mPD178053

D-Link DSN-640 Quick Installation Manual preview
DSN-640
Бренд: D-Link Страницы: 40
IFM Electronic ecomat 100 R 360 Operating Instructions Manual preview
ecomat 100 R 360
Бренд: IFM Electronic Страницы: 16
IFM Electronic AC1331 Installation Instructions Manual preview
AC1331
Бренд: IFM Electronic Страницы: 23
National Instruments NI-488.2 Getting Started preview
NI-488.2
Бренд: National Instruments Страницы: 7
National Instruments GPIB-SCSI-A Installation Manual preview
GPIB-SCSI-A
Бренд: National Instruments Страницы: 16
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Бренд: Yamaha Страницы: 92
YOKOGAWA TC 10-L Engineering Manual preview
TC 10-L
Бренд: YOKOGAWA Страницы: 20
YOKOGAWA UTAdvanced UT32A Technical Information preview
UTAdvanced UT32A
Бренд: YOKOGAWA Страницы: 3
Zener SMARTSTART 6000 Networking Manual preview
SMARTSTART 6000
Бренд: Zener Страницы: 36
Zapi SMART CONSOLE Instructions preview
SMART CONSOLE
Бренд: Zapi Страницы: 5
Eaton S611 User Manual preview
S611
Бренд: Eaton Страницы: 96
CalAmp LMU 2630MB Installation Manual preview
LMU 2630MB
Бренд: CalAmp Страницы: 13
National Instruments PXI-8150B User Manual preview
PXI-8150B
Бренд: National Instruments Страницы: 78
Nemesis OSCA-I8 User Manual preview
OSCA-I8
Бренд: Nemesis Страницы: 6
PENGWYN 485-1P-JS Technical Manual preview
485-1P-JS
Бренд: PENGWYN Страницы: 32
Warner Electric CBC-801-1 Installation Instructions And Service Manual preview
CBC-801-1
Бренд: Warner Electric Страницы: 6
PENKO 1020 CAN-RS232-RS422 MFL Manual preview
1020 CAN-RS232-RS422 MFL
Бренд: PENKO Страницы: 29
Bettis TEC2 Quick Start Manual preview
TEC2
Бренд: Bettis Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды