NEC mPD178053 Скачать руководство пользователя страница 180

Страница: 180 / 271

180

CHAPTER 13 PLL FREQUENCY SYNTHESIZER

User’s Manual U15104EJ2V0UD

(1) PLL data register L (PLLRL), PLL data register H (PLLRH), and PLL data register 0 (PLLR0)

These registers set the division value of the PLL frequency synthesizer. The division value of the PLL

frequency synthesizer is made up of 17 bits. The higher 16 bits of this value are set by PLL data register L

(PLLRL) and PLL data register H (PLLRH). The higher 16 bits can also be set by the PLL data register (PLLR).

The least significant bit is set by bit 7 (PLLSCN) of PLL data register 0 (PLLR0).

Reset input makes the contents of these registers undefined. These registers hold the current values in the

STOP and HALT modes.

(2) Input select block

The input select block consists of the VCOL and VCOH pins, and input amplifiers of the respective pins.

(3) Programmable divider

The programmable divider consists of two modulus prescalers, a programmable counter (12 bits), a swallow

counter (5 bits), and a division mode select switch.

(4) Reference frequency generator

The reference frequency generator consists of a divider that generates the reference frequency f

of the PLL

frequency synthesizer, and a multiplexer.

(5) Phase comparator

The phase comparator (

-DET) compares the phase of the divided frequency output f

of the programmable

divider with that of the reference frequency output f

of the reference frequency generator, and outputs an up

request signal (UP) and down request signal (DW).

(6) Unlock F/F

The unlock F/F detects the unlock status of the PLL frequency synthesizer from the up request signal (UP)

and down request signal (DW) of the phase comparator (

-DET).

(7) Charge pump

The charge pump outputs the result of the output of the phase comparator from the error out pins (EO0 and

EO1 pins).

Содержание mPD178053
















































































































































































































































































Результаты поиска

Содержание mPD178053

Отзывы:

Похожие инструкции для mPD178053

Бренды по названию

Популярные бренды

NEC mPD178053, Руководство пользователя

Результаты поиска

Содержание mPD178053

Отзывы:

Похожие инструкции для mPD178053

Бренды по названию

Популярные бренды