NEC Electra Elite 48/192 Скачать руководство пользователя страница 462 | Manualshive

Страница: 462 / 652

background image

Features and Specifications Manual

P - 5

PC Programming

P-2

FEATURE
DESCRIPTION

The MIFM-U10 ETU and System Administration Terminal (SAT) software allow
the system to be programmed from a personal computer (PC). System Data is
transferred to/from a diskette for backup of system data. SAT PC
programming software also allows the user to print station designation strips
to shorten installation time. End users can use end-user SAT PC programming
software to program several features for their Multiline Terminals such as: Line
Key Assignment, Telephone Names, Zone Paging Groups, or various
programmed times.

SYSTEM
AVAILABILITY

Terminal Type:

Not applicable

Required Components:

MIFM-U10 ETU

Pentium PC with Windows 95 or higher to run SAT PC programming

OPERATING
PROCEDURES

SERVICE
CONDITIONS

Data Assignment:

Use Memory Block 1-8-17 (PC Programming Password Assignment) to
set a system password that must be entered when using PC
Programming.

Use Memory Block 1-8-18 (Site name Assignment) to enter a system
name (8 digits maximum) to use to program the system.

Use Memory Block 1-8-35 (COM Port Baud Rate Setting Assignment) to
individually define the baud rate for COM ports.

Use Memory Block 1-8-36 (COM Port Parity/Stop Bit setting
Assignment) to individually define the Parity and Stop Bit for COM ports.

Refer to the Electra Elite Programming Manual for PC
programming instructions.

«
...
460
461
462
463
464
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: Acer Страницы: 2

Бренд: Acer Страницы: 4

Бренд: Kargo Master Страницы: 5

Бренд: Kappa Страницы: 4

imagePROGRAF iPF830

Бренд: Canon Страницы: 16

Бренд: Canon Страницы: 6

Бренд: 4B Страницы: 12

Бренд: Samsung Страницы: 128

Бренд: Samsung Страницы: 33

Бренд: Samsung Страницы: 2

Бренд: Jeep Страницы: 7

Бренд: DAC Limited Страницы: 12

Бренд: Harken Hoister Страницы: 12

Бренд: Ultratec Страницы: 28

Бренд: UltraGauge Страницы: 55

ShowMatch DeltaQ SMGSB

Бренд: Bose Страницы: 2

Бренд: Vortice Страницы: 132

Бренд: Blue Ox Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды