NEC Electra Elite 48/192 Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 652

background image

Electra Elite

Issue 6

Features and Specifications Manual

C - 47

General:

Features like Code restriction, or forced account codes that are
enabled for the Call Forward – Off-Premise extension apply to any
call that follows Call forward – Off-Premise.

The Feature key LED flashes red when Call Forward – Off-Premise
(All Calls) is set from a Multiline Terminal.

The ACD/UCD overflow destination station can be set to Call
Forward – Off-Premise.

The Access Codes for Call Forward set and cancel can be
programmed on Feature Access keys or One-Touch keys. Press the
key during the conversation with an internal or outside party to place
the call on hold and dial the Access Code.

When a Call Forward ON/OFF key (All Call or Busy/No Answer) is
programmed on the line key, set/cancel toggles. The Trunk Access
Code and destination outside number must be dialed after pressing
this key when setting Call Forward – Off-Premise.

Incoming calls from a voice mail system follow the Call
Forward – Off-Premise setting.

The Call Arrival (CAR) key number can be set for Call
Forward – Off-Premise. System Software S4000 or higher is
required.

The Speed Dial number cannot be set as the destination forward
number.

When the system is installed in the Key Function (KF) mode, a
Specified Line Seizure Access Code must be used when setting Call
Forward – Off-Premise.

The following incoming calls can be forwarded:

•

CO/PBX Transfer Call

•

Ordinary Incoming Internal Call

•

Direct Inward Termination (DIT)

•

Assigned Night Answer (ANA)

•

Direct Inward Dialing (DID)

•

Tie Line (TIE)

•

Automated Attendant (AA)

When the outside party, where the call is forwarded, is busy or does
not answer, the call is terminated when the calling party hangs up.

«
...
164
165
166
167
168
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: Veris Industries Страницы: 2

Бренд: Lauterbach Страницы: 67

Бренд: Samsung Страницы: 2

Бренд: 3Doodler Страницы: 24

Q.HOME+ ESS HYB G2

Бренд: Qcells Страницы: 2

Бренд: Uniden Страницы: 20

Бренд: Raven Страницы: 70

Бренд: Xorcom Страницы: 9

DVX-2000MS-10P - VoiceCenter IP Phone Sys...

Бренд: D-Link Страницы: 20

Бренд: Fabbri Страницы: 4

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды