NEC Electra Elite 48/192 Скачать руководство пользователя страница 338 | Manualshive

Страница: 338 / 652

background image

Features and Specifications Manual

E - 35

External Tone Ringer

E-10

FEATURE
DESCRIPTION

The External Tone Ringer provides a common audible tone with relay contacts
for control when incoming CO/PBX calls are received in Day or Night Mode.
The relay contact closures may be used for external bells or chimes. When an
Attendant is not available, station users may respond to the external ring and
answer incoming calls. This feature provides for wide area coverage or loud
ringing for noisy locations where incoming CO/PBX calls are answered.

SYSTEM
AVAILABILITY

Terminal Type:

Not applicable

Required Components:

ECR-U10 ETU for common audible and control relays

OPERATING
PROCEDURES

SERVICE
CONDITIONS

Data Assignment:

Use Memory Block 1-7-07 (External Ring Delay Pattern Selection) to
assign each External Tone Ringer control circuit to one of five distinctive
ringing patterns (default: Pattern 3), including continuous ring.

Use Memory Block 2-08 (ECR Relay to Tenant Assignment) to assign an
External Tone Ringer control relay to a tenant to control tone generation.

Use Memory Block 7-1 (Card Interface Slot Assignment) to specify the
ECR-U10 ETU.

Restrictions:

A maximum of four relays are programmable for External Tone Ringer
control.

Tie lines, DIT/ANA calls, and DID trunks do not activate the External
Tone Ringer control relays.

None

«
...
336
337
338
339
340
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: NEC Страницы: 3

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 2

Бренд: JANE Страницы: 6

Бренд: 2N Страницы: 21

Бренд: 2N Страницы: 59

Бренд: IFM Страницы: 43

Green Motion DC 22

Бренд: Eaton Страницы: 65

Бренд: PASCO Страницы: 3

witty park XEV6 Series

Бренд: hager Страницы: 9

Бренд: Xerox Страницы: 10

6130N - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренд: Varta Страницы: 132

Krisp Socket Assembly Kit For Straight and Offset...

Бренд: Keating Of Chicago Страницы: 1

Бренд: Karel Страницы: 13

Бренд: Ikan Страницы: 2

Бренд: PNI Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды