NEC Electra Elite 48/192 Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 652

background image

C - 40

Call Forward - Centrex

Issue 6

Electra Elite

Setting, canceling or Call Forwarding is allowed only when logged
out of ACD.

General:

Even when a user is logged on as an ACD agent, an individual call
that does not come through the Pilot Number is forwarded.

Call Forward - Centrex supports the following:

•

Call Forward - All

•

Call Forward - Busy

•

Call Forward - No Answer

•

Call Forward - Busy/No Answer

•

Call Forward - All for CAR

•

Call Forward - Busy/No Answer for CAR

Call Forward - Centrex calls transferred from another station are
forwarded when the transferred Trunk is assigned as Centrex in
Memory Block 3-91 (Trunk Type Selection).

When a Centrex Trunk is DIT to a station with Call Forward - Centrex
set with an incorrect registered number, the Centrex trunk recalls to
the same number until the caller hangs up.

The following incoming calls follow Call Forward - Centrex when the
incoming trunk is a Centrex trunk:

•

DIT/ANA

•

Station Transfer

•

Automated Attendant Transfer

•

DISA Calls

When Call Forward - Centrex is set and all trunks are changed from
PBX/CTX to CO, Call Forward is cleared from memory.

When a station is logged in an as ACD agent and Call Forward-Busy/
No Answer is set, any non-ACD call transferred or ringing to that
station follows the Call Forward setting. System software S5000 or
higher is required.

«
...
157
158
159
160
161
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: GÄN Страницы: 24

Alerts TX60U-IT

Бренд: La Crosse Technology Страницы: 3

Бренд: Napoleon Страницы: 4

Бренд: Labona Страницы: 12

HighLine ABF0166

Бренд: Mactronic Страницы: 2

Бренд: Swann Страницы: 12

Бренд: Satlink Страницы: 16

Бренд: FORM FIT Страницы: 2

Бренд: Hettich Страницы: 2

Бренд: CEECO Страницы: 12

Бренд: Waeco Страницы: 124

Бренд: IKEA Страницы: 12

Бренд: Gared Sports Страницы: 12

Бренд: HQ Страницы: 2

Бренд: AA Products Страницы: 4

Wireless Rain Sensor

Бренд: R&D Страницы: 8

Бренд: Uniden Страницы: 8

Бренд: Magicshine Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды