NEC Electra Elite 48/192 Скачать руководство пользователя страница 446 | Manualshive

Страница: 446 / 652

background image

Features and Specifications Manual

N - 7

Night Chime

N-3

FEATURE
DESCRIPTION

Night Chime provides a common audible tone with one relay contact for
control when incoming CO/PBX calls are received in Night Mode. The relay
contact closures may also be used for external bells or chimes. The Night
Chime feature is used after working hours to alert night personnel for incoming
outside calls.

SYSTEM
AVAILABILITY

Terminal Type:

Not applicable

Required Components:

ECR-U10 ETU for common audible tone and control relay

OPERATING
PROCEDURES

SERVICE
CONDITIONS

Data Assignment:

Use Memory Block 2-08 (ECR Relay to Tenant Assignment) to specify
Tenant assignment (LED On) to External Tone Relay 1, 2, 3, 4, or Night
Chime function for the ECR Relay. Default is unassigned.

Use Memory Block 7-01 (Card Interface Slot Assignment) to specify the
ECR-U10 ETU.

Restrictions:

Tie/DID lines, DIT/ANA calls, and Automated Attendant do not activate
the Night Chime relay.

General:

An ECR-U10 ETU is required for common audible tone and control
relays. Ten relays are provided with this ETU. One relay is provided for
Night Chime control.

The Night Chime control relay is activated based on Night Mode of each
Tenant group.

None

«
...
444
445
446
447
448
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: Manfrotto Страницы: 2

Univerge SV8100

Бренд: NEC Страницы: 1174

Бренд: Garmin Страницы: 26

Бренд: Garmin Страницы: 8

Бренд: Garmin Страницы: 72

Бренд: Natibaby Страницы: 24

Бренд: Narvitech Страницы: 12

Бренд: Valcom Страницы: 1

Бренд: Valcom Страницы: 13

Бренд: Veeder-Root Страницы: 2

Бренд: D-Link Страницы: 58

Бренд: Waterpik Страницы: 2

Бренд: Sacred Sun Страницы: 19

Бренд: iDataLink Страницы: 99

Бренд: REV Страницы: 2

1306 RAPID SYSTEM

Бренд: Thule Страницы: 8

Бренд: Woody Valley Страницы: 15

Бренд: Aastra Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды