NEC Electra Elite 48/192 Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 652

background image

Features and Specifications Manual

D - 27

Direct Inward Dialing (DID)

D-9

FEATURE
DESCRIPTION

Direct Inward Dialing (DID) lines can be connected to the system. With DID,
incoming calls from the CO can reach any station in the system without
Attendant intervention.

System Software S4000 or higher allows sending DID calls to a tenant.

System Software S5000 or higher allows DID calls to be answered by the
Automated Attendant.

System Software S5000 or higher allows limiting the number of incoming
DID calls to a tenant.

SYSTEM
AVAILABILITY

Terminal Type:

All Multiline Terminals

Required Components:

DID(4)-U10 ETU, PRT(1)-U10/20 ETU, or DTI-U10/20 ETU

OPERATING
PROCEDURES

SERVICE
CONDITIONS

Data Assignment:

Incoming DID numbers can be routed to any station in the system
regardless of the numbering plan. When an incoming DID number is
invalid, the call can be sent to a preassigned station or hunt group pilot
number.

Use Memory Block 5-00 (Digit Add/Del for Tie Line Networking
Assignment) to add and/or delete a maximum of two digits per trunk
group, from the incoming DID digits provided by the DID trunk for
incoming address signaling. Setting 0 allows DID Full Digit Modification
that collects the incoming digits and sends the call to a specified station
number.

None

«
...
234
235
236
237
238
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

LevelMaster 7100

Бренд: ABB Страницы: 28

Ability Smart Sensor

Бренд: ABB Страницы: 4

Бренд: ABB Страницы: 20

Бренд: Aastra Страницы: 2

Бренд: Metra Electronics Страницы: 14

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Speedglas 9100-Air

Бренд: 3M Страницы: 63

Бренд: 3M Страницы: 84

Бренд: Patton electronics Страницы: 12

Бренд: Q'STRAINT Страницы: 10

Бренд: Xerox Страницы: 2

Бренд: Westin Страницы: 3

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Бренд: Carax Страницы: 2

Бренд: FujiFilm Страницы: 13

Бренд: Scame electrical solutions Страницы: 8

Бренд: Prorack Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды