NEC Electra Elite 48/192 Скачать руководство пользователя страница 614 | Manualshive

Страница: 614 / 652

background image

Features and Specifications Manual

U - 15

Universal Slots

U-4

FEATURE
DESCRIPTION

Universal Slots provide flexibility for installation and cost savings for the end
user. The system allows the installation of most interface circuit boards in any
interface slot.

SYSTEM
AVAILABILITY

Terminal Type:

Not applicable

Required Components:

None

OPERATING
PROCEDURES

SERVICE
CONDITIONS

General:

The Electra Elite 192 system B64-U10 KSU has eight universal slots,
and the system uses the same KSU for the basic and expansion units.

The Electra Elite 48 system B48-U10 KSU has four universal slots with
MDF connections, and two slots without MDF connections.

The MIFM-U10 ETU or MIFA-U10 ETU must be installed in the ISA, S1,
or S2 slot of the B64-U10 KSU or slot S2 of the B48-U10 KSU.

The DTI-U10/20 ETU must be installed in slot S1 or S4 of the basic
B64-U10 KSU or slot S1 of the first expansion B64-U10 KSU for Electra
Elite 192. It must be installed in slot S4 of the B48-U10 KSU for the
Electra Elite 48 system.

Universal Slots allow interfacing for the following:

•

BRT(4)-U10 ETU (4 port ISDN Interface for 8 trunks)

•

BSU(2)-U10 ETU (Base Station Unit)

•

CNF(8)-U10 ETU (Multiline Conference Unit)

•

COI(8)-U10 ETU (8 port CO/PBX Line Interface)

None

«
...
612
613
614
615
616
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: Manfrotto Страницы: 4

Бренд: TaylorMade Страницы: 5

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 32

Бренд: Waycon Страницы: 4

Бренд: Yakima Страницы: 11

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

OLYMPIA 3x3.05m/10

Бренд: Palram Applications Страницы: 65

Бренд: T-Home Страницы: 52

Бренд: WABASH COMMUNICATIONS Страницы: 17

Бренд: Majestic Страницы: 4

Wireless Service Gateway WSG

Бренд: Unify Страницы: 39

Бренд: Roav Страницы: 10

Бренд: SUP’AIR Страницы: 29

Бренд: FujiFilm Страницы: 13

Бренд: Scame electrical solutions Страницы: 8

Бренд: Heitronic Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды