NEC Electra Elite 48/192 Скачать руководство пользователя страница 427 | Manualshive

Страница: 427 / 652

background image

M - 4

Message Waiting

Issue 6

Electra Elite

Dial

K

or the associated Attendant station with the Attendant Add-On

Console used to set the message.

- OR -

Call the Voice Mail System, and retrieve the messages.

SERVICE
CONDITIONS

Data Assignment:

Use Memory Block 1-6-05 (Attendant Add-On Console Key
Selection) to assign the Message Waiting function to an Attendant
Add-On Console key.

General:

A Message Waiting indication is provided on the large LED on the
recipient Multiline Terminal. Message Waiting indications from the
Attendant Add-On Console flash green; indications from a Voice Mail
Unit flash red.

To confirm a Message Waiting indication at an Attendant Add-On
Console, ensure that the green LED associated with the station is on.
A Message Waiting indication remains on until the message is
canceled at the Attendant Add-On Console where it was set.

When two or more (maximum of four per system) Attendant Add-On
Consoles are installed, the message is displayed only on the
Attendant Add-On Console where the setting was made.

All Attendant Add-On Consoles can be used to set a Message
Waiting to the same station.

Single Line Telephones supported by an SLI(8)-U10 ETU with a
Message Waiting LED receive a flashing Message Waiting indication
when set.

A Voice Mail system can set and cancel the messages to stations.

Message Waiting from an Attendant Add-On Console has higher
priority than Message Waiting from a Voice Mail Unit.

An Attendant Add-On Console with a Message Waiting key assigned
on it cannot be used to set the Attendant Station Outgoing Lockout
feature.

Message Waiting status is retained in memory by the memory
backup battery.

To respond to Message Waiting indication:

«
...
425
426
427
428
429
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: Manfrotto Страницы: 2

Бренд: Manfrotto Страницы: 2

Бренд: Waycon Страницы: 8

Бренд: Yealink Страницы: 2

Бренд: Lauterbach Страницы: 67

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: Datalogic Страницы: 248

Line FP7000 Housing

Бренд: Fantasea Страницы: 5

Бренд: Fantasea Страницы: 5

Бренд: Fancom Страницы: 49

Бренд: FANATEC Страницы: 2

Бренд: Viewpro Страницы: 10

Бренд: Uniden Страницы: 44

Бренд: Waterpik Страницы: 20

Water Flosser WF-06

Бренд: Waterpik Страницы: 2

Бренд: Waterpik Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды