NEC Electra Elite 48/192 Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 652

background image

C - 62

Centralized Voice Mail

Issue 6

Electra Elite

Use Memory Block 1-2-04 (Call Arrival Key Block Assignment) to
assign the CAR key that is used to deliver message-waiting
notification to the systems in the Closed Numbering Network. This is
common to all systems that have Centralized Voice Mail.

Use Memory Block 4-10 (Station Number Assignment) to assign the
Voice Mail Ports and the Call Arrival Key station numbers.

Use Memory Block 1-8-47 (Call Arrival Key Voice Mail Message
Notification Assignment) to assign the CAR Key used to send Voice
Mail Message Notification to other systems in the Closed Numbering
Network.

Use Memory Block 4-14 (Intercom Master Hunt Number Selection)
to assign a voice mail master hunt number. This memory block is
used only for the system that has Voice Mail.

Use Memory Block 4-15 (Intercom Master Hunt Number Forward
Assignment) to specify the hunt group for voice mail ports. This
memory block is used only for the system that has Voice Mail.

Use Memory Block 1-08-08 [Class of Service (Station) Feature
Selection 2] Page 3 LK5 to Allow (LED ON) station trunk-to-trunk
Transfer.

Use Memory Block 1-08-08 [Class of Service (Station) Feature
Selection 2] Page 5 LK4 to Allow (LED ON) Call Forward – Off-
Premise.

Use Memory Block 3-04 (Trunk-to-Trunk Transfer Yes/No Selection)
to allow (LED ON) trunk-to-trunk transfer between systems in the
Closed Numbering Network.

Use Memory Block 1-2-24 (Intercom Feature Access Code
Assignment) to assign Quick Transfer to Voice Mail access code
007. This memory block is used only for the system that has Voice
Mail.

Use Memory Block 1-8-26 (Voice Mail Quick Transfer Master Hunt
Number) to assign a number for the Voice Mail.

Use Memory Block 1-1-46~48 [Access Code (1-, 2-, or 3-Digit)
Assignment] to assign dial access codes for Closed Number Block 1
(Function 401~416) and Message Waiting set (Function 502) and
Message Waiting Cancel (Function 503).

Use Memory Block 1-1-49 (Networking Trunk Group/Route Advance
Assignment) to assign the trunk group used by the Closed
Numbering Block.

Use Memory Block 1-1-50 (CO/PBX Outgoing Digit Assignment) to
specify the digits added for a Closed Numbering Block.

«
...
179
180
181
182
183
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 30

Event Master E2

Бренд: Barco Страницы: 2

Бренд: Barco Страницы: 7

Бренд: Barco Страницы: 7

Бренд: Tailfin Страницы: 8

Бренд: CAME Страницы: 4

Formula F732 WIZARD

Бренд: Datalogic Страницы: 2

HOIST-A-TOP JL CRANK

Бренд: Lange Originals Страницы: 13

Бренд: Xorcom Страницы: 9

Бренд: Uebler Страницы: 18

Бренд: Smartech Страницы: 8

Бренд: Produal Страницы: 9

Бренд: Aroflora Страницы: 36

Бренд: KEDO Страницы: 2

Бренд: KEDO Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды