NEC Electra Elite 48/192 Скачать руководство пользователя страница 180 | Manualshive

Страница: 180 / 652

background image

Features and Specifications Manual

C - 61

Centralized Voice Mail

C-16

FEATURE
DESCRIPTION

Centralized Voice Mail allows two or more systems that are connected by
Analog or Digital T1 Lines to share one Voice Mail (VM) system. This feature
allows VM Box access from Intercom (ICM)/CO/Automated Attendant, VM
message LED indication, or Call forward – Off-Premise to a VM port. The Elite
system communicates Message Waiting (MW) LED, Mailbox and other
information using DTMF Signaling between two Elite systems.

System Software S5000 or higher is required.

SYSTEM
AVAILABILITY

Terminal Type:

All Multiline Terminals

Required Components:

CTI/VP(4)/(8)/(12)/(16)-U10 ETU

VMS(2)/(4)/(8)-U10 ETU

FMS(2)/(4)/(8)-U10 ETU

DTI-U10/20 ETU

TLI(2)-U10 ETU

OPERATING
PROCEDURES

SERVICE
CONDITIONS

Data Assignment:

Use Memory Block 7-1 (Card Interface Slot Assignment) to specify the
SLT ETU for Analog System or a VMS/FMS/CTI/VP ETU (using Page 3,
Line Key 3 or 4) for Digital Voice Mail systems. This memory block is
used only for the system that has Centralized Voice Mail.

Use Memory Block 7-2 (Telephone Type Assignment) to specify the
Digital Voice Mail ports. This memory block is used only for the system
that has Centralized Voice Mail.

Refer to the Voice Mail manuals.

«
...
178
179
180
181
182
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: Canon Страницы: 12

Бренд: CAME Страницы: 2

Бренд: N-Com Страницы: 28

Бренд: Gates Страницы: 2

AJHVF21G - HD EVF - MULTI-LANG

Бренд: Panasonic Страницы: 4

Бренд: Samsung Страницы: 2

MMAC-Plus 9F116-01

Бренд: Cabletron Systems Страницы: 4

Бренд: Caberg Страницы: 16

Heating Overblanket

Бренд: Lanaform Страницы: 84

Бренд: Lanaform Страницы: 84

Бренд: Lanaform Страницы: 72

Бренд: Lanaform Страницы: 80

Бренд: Lanier Страницы: 3

Бренд: Varta Страницы: 2

DVX-2000MS-10P - VoiceCenter IP Phone Sys...

Бренд: D-Link Страницы: 20

Бренд: Fabbri Страницы: 4

Бренд: BAFANG Страницы: 9

DS-KABD8003-RS3

Бренд: HIKVISION Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды