NEC Electra Elite 48/192 Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 652

background image

C - 54

Call Park - System

Issue 6

Electra Elite

1.

Go off-hook, and wait for internal dial tone.

2.

Dial the Call Park Retrieve Access Code

DL

(set as

default).

3.

Dial the Call Park location number (

K

~

I

) of the call to be

retrieved.

4.

Talk with party.

SERVICE
CONDITIONS

Data Assignment:

Use Memory Blocks 1-1-46~48 [Access Code (1-, 2-, or 3-Digit)
Assignment] to assign Access Code (4# for Call Park System Answer
or 4* for Call park System Transfer).

Use Memory Block 1-2-23 (System Call Park Recall Time Selection),
to specify the time (default: 1 minute) before a parked call recalls
back to a station.

General:

Any call left in Call Park more than the programmed time recalls to
the station where the call was originally parked. The Call Park
location becomes idle after the recall, and the trunk line key switches
to Non-Exclusive Hold.

When attempting to set Call Park to a busy Call Park location, and a
busy tone is heard, Step Call can be used to access an idle location
to park the call.

When a station other than the station originally used to park the call
retrieves the call, the SMDR records a transfer to the station where
the call is retrieved.

When a Call Park is in recall mode, the call cannot be picked up
using the Call Park retrieval Access Code.

Call Park is set and retrieved from internal dial tone.

Outside calls and internal calls can be parked from any station.

Conference calls cannot be parked.

When attempting to set Call Park and all Call Park locations are busy,
a busy tone is heard and ALL PARK BUSY is displayed on Display
Multiline Terminals.

To retrieve a parked call at either a Multiline Terminal or a Single
Line Telephone:

«
...
171
172
173
174
175
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 3

ECONAVI CZ-CENSC1

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 9

AR42P9W - Plasma Panel anti-glare Filter

Бренд: Panasonic Страницы: 5

Бренд: Tamron Страницы: 3

BTL7-S5 B-M Series

Бренд: Balluff Страницы: 14

BML-S1G0 7 M5E 0 Series

Бренд: Balluff Страницы: 194

and Vantage Pro

Бренд: DAVIS Страницы: 4

and Vantage Pro

Бренд: Davis Instruments Страницы: 4

Бренд: Datavideo Страницы: 45

Бренд: RaceChip Страницы: 12

Бренд: JASTEC Страницы: 12

Бренд: parktool Страницы: 2

Бренд: AT&T Страницы: 116

Бренд: Manfrotto Страницы: 2

Бренд: La Crosse Technology Страницы: 6

Бренд: Labelmate Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды