NEC Electra Elite 48/192 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 652

background image

Electra Elite

Issue 6

Features and Specifications Manual

A - 7

Use Memory Block 1-8-08 [Class of Service (Station) Feature
Selection 2], Page 6 LK3 to Allow (LED On) or Deny (default: LED
Off) Account Code Forced/Unverified. System software S5000 or
higher is required.

Use Memory Blocks 1-1-46~48 [Access Code (1-, 2-, or 3-Digit)
Assignment] to assign the Forced Account Code Access (Function
No. 147).

Use Memory Block 1-8-27 (Forced Account Code Length
Assignment) to assign the number of digits for Account Codes
system-wide. One to 13 digits can be assigned; default is 10 digits.

Use Memory Block 7-1 (Card Interface Slot Assignment) to specify
the necessary MIFM-10 ETU.

Restrictions:

Existing restrictions and Least Cost Routing (LCR) assignments are
applied after Forced Account Codes are entered.

When a 911 call is placed, Account Code Forced/Verified is
overridden by the following:

•

Emergency 911 Cut-Through is enabled.

•

A CAMA trunk is installed and enabled.

Enhanced 911 calls override the forced account code and are
controlled by the Emergency 911 Dialing Route Assignment.

Verified and Unverified Forced Account Codes cannot be used in the
same Class of Service.

General:

System Software S5500 or higher is required for Scrolling
Directories to be used with this feature.

Only outgoing calls from an intercom require a Forced Account
Access Code. Direct access to trunks bypasses this feature.

Reorder tone is provided when an outgoing call is dialed without
entering the Forced Account Access Code and a Forced Account
Code.

Call Alert Notification is not provided during Account Code Entry
verification and programming.

PBR Time values apply when a Single Line Telephone is used to
enter a Forced Account Code.

Forced Account Codes can be uploaded, downloaded, or modified
using PC based System Programming.

«
...
26
27
28
29
30
...
»

Содержание Electra Elite 48/192













































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Electra Elite 48/192

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 3

ECONAVI CZ-CENSC1

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 9

AR42P9W - Plasma Panel anti-glare Filter

Бренд: Panasonic Страницы: 5

Бренд: Tamron Страницы: 3

Бренд: AA Products Страницы: 8

Бренд: AAMP of America Страницы: 6

Бренд: rako Страницы: 7

Бренд: Saft Страницы: 6

Бренд: Safeline Страницы: 32

AERASGARD RCO2-W

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 56

Бренд: Miditech Страницы: 11

Бренд: Adam Страницы: 22

Бренд: BS Bodensteckdosen Systemtechnik Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды