NEC 78K0/KB1+ Скачать руководство пользователя страница 289

Страница: 289 / 405

CHAPTER 14 INTERRUPT FUNCTIONS

Preliminary User’s Manual U16846EJ1V0UD

289

14.4.3 Multiple interrupt servicing

Multiple interrupt servicing occurs when another interrupt request is acknowledged during execution of an interrupt.

Multiple interrupt servicing does not occur unless the interrupt request acknowledgment enabled state is selected

(IE = 1). When an interrupt request is acknowledged, interrupt request acknowledgment becomes disabled (IE = 0).

Therefore, to enable multiple interrupt servicing, it is necessary to set (1) the IE flag with the EI instruction during

interrupt servicing to enable interrupt acknowledgment.

Moreover, even if interrupts are enabled, multiple interrupt servicing may not be enabled, this being subject to

interrupt priority control. Two types of priority control are available: default priority control and programmable priority

control. Programmable priority control is used for multiple interrupt servicing.

In the interrupt enabled state, if an interrupt request with a priority equal to or higher than that of the interrupt

currently being serviced is generated, it is acknowledged for multiple interrupt servicing. If an interrupt with a priority

lower than that of the interrupt currently being serviced is generated during interrupt servicing, it is not acknowledged

for multiple interrupt servicing.

Interrupt requests that are not enabled because interrupts are in the interrupt disabled state or because they have

a lower priority are held pending. When servicing of the current interrupt ends, the pending interrupt request is

acknowledged following execution of at least one main processing instruction execution.

Table 14-5 shows relationship between interrupt requests enabled for multiple interrupt servicing and Figure 14-10

shows multiple interrupt servicing examples.

Table 14-5. Relationship Between Interrupt Requests Enabled for Multiple Interrupt Servicing

During Interrupt Servicing

Multiple Interrupt Request

Maskable Interrupt Request

PR = 0

PR = 1

Interrupt Being Serviced

IE = 1

IE = 0

IE = 1

IE = 0

Software

Interrupt

Request

ISP = 0

Maskable interrupt

ISP = 1

Software interrupt

Remarks 1. : Multiple interrupt servicing enabled

: Multiple interrupt servicing disabled

3. The ISP and IE are flags contained in the PSW.

ISP = 0: An interrupt with higher priority is being serviced.

ISP = 1: No interrupt request has been acknowledged, or an interrupt with a lower

priority is being serviced.

IE = 0:

Interrupt request acknowledgment is disabled.

IE = 1:

Interrupt request acknowledgment is enabled.

4. PR is a flag contained in PR0L, PR0H, and PR1L.

PR = 0: Higher priority level

PR = 1: Lower priority level

Содержание 78K0/KB1+






















































































































































































































































































































































































































Результаты поиска

Содержание 78K0/KB1+

Отзывы:

Похожие инструкции для 78K0/KB1+

Бренды по названию

Популярные бренды

NEC 78K0/KB1+, Предварительное руководство пользователя

Результаты поиска

Содержание 78K0/KB1+

Отзывы:

Похожие инструкции для 78K0/KB1+

Бренды по названию

Популярные бренды