L
NAPCO Security Systems
X
GEM-P1632 Programming Instructions
!
Page 17
RF Transmitter Points
(Press the
(
R
)
button
to set cursor)
(For wireless systems only.
Also see Quick Method, which follows).
For each transmitter (key fob transmitters also), enter the zone number (01–48) to which the
transmitter will be mapped, the 6-digit RF ID#: 1-digit checksum number printed on the transmitter and
box, the point number (1–4);
enter “9” for unsupervised
(all points).
NOTE:
When programming the
ID Code number, “A” =
G
0
; “B” =
G
1
; “C” =
G
2
; “D” =
G
3
;
“E” =
G
4
; “F” =
G
5
. Press
J
to save. Press NEXT (
E
) to proceed.
GEM-
RP3DGTL/GEM-K3
DGTL A
N
D
GEM-RP4RFC/GEM
-K
4RF Ea
s
y Me
nu Dri
ven
Pr
ogr
am Mode
Related User Options:
“Enable Global Ambush Code” (Address 0720) & “Global Ambush
Code” (Address 1054).
CODE TYPE
EXPLANATION
Disabled
User Code not active.
Arm/Disarm
Allows User Code to arm/disarm.
Arm Only
Prevents User Code from disarming.
Service
A Service Code has restricted arm/disarm rights; if an area is armed with a Service
Code, a “
SERVICE ON
” appears on the GEM-RP2ASe2 keypad and the area can be
disarmed with any valid User Code, including a Service Code. If the area is armed
with OTHER than a Service Code, it CANNOT be disarmed with a Service Code.
This is typically used to allow tradesmen access to premises under control of the
owner.
Access
This is normally used to activate a door strike. Also program “Access Control on
PGM2 Output” (Address 0719) and “PGM2 Output Access Control
Timeout” (Address 0711).
Ambush
This code is entered by user to disarm and activate an "Ambush Alarm", causing
a report to be sent to central station. Also program Ambush to report to C.S.,
Report Code, Sub I.D.
* User Program User Program Option is enabled for Keypad 1 only, wherever it is connected. To
enable User Program Option for any user add 8 to the data entry Option (see
example). Then, User Programming can be performed only at Keypad 1 by a user
code with user program enabled.
USER OPTIONS:
Area 1 and 2 options for 32
Users:
!
Select the desired options from the table
shown and enter in the remaining two
boxes for each user code.
OPTION
ENABLED
Disabled
Arm/Disarm
Arm Only
Service
Access
Ambush
* User Program
L
R
blank(•) blank
blank(•)
1
blank(•)
2
blank(•)
3
blank(•)
4
blank(•)
5
DATA ENTRIES
blank(•) Add 8
USER OPTIONS
USER CODE
(UP TO 6 DIGITS)
AREA 1
OPTIONS
AREA 2
OPTIONS
Example:
Program a code of “1234” for user 02,
with Area 1 options of “Arm/Disarm” and “User
Program”:
With “27” displayed in keypad window, press
R
,
0
2
(User 2),
R
1234
,
G
0
G
0
(User Code),
09
(User Area 1
options),
00
(User Area 2 Options), and
U
(save).
Notes:
(1) For
User Code
, press
G
0
for Blank Space; (2) For
User Options
, press
0
for Blank Space.
28
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
Quick Method
.
If a receiver is already installed in the panel, Napco transmitter
wireless points can be programmed automatically (“enrolled”)
using the following procedure.
NOTE:
The transmitter point will
be enrolled only if the signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be
mapped.
2. Press the
B
button to enter the Enroll Mode. The red and
green LEDs on the keypad will flash and the window will
display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-
TRANS2 or GEM-TRANS4 only).
4. Install the transmitter battery. The keypad will beep to indicate
that the point has been successfully enrolled. Multi-point
transmitters can be mapped to successive zones
simultaneously (Example 1) or to selected zones point by
point (Example 2).
Example 1.
A 4-point transmitter has the RF ID number
410078:1.
Map the first three points to Zones 11–13,
respectively.
1. Enter the Enroll mode as described in step 2 above.
2. Enter Zone “11”.
3. Open the loops of points 1, 2 and 3.
4. Install the transmitter battery. The keypad will beep 3 times to
indicate that three points have been programmed.
!
Transmitter 410078:1, point 1 will be mapped to Zone 11.
!
Transmitter 410078:1, point 2 will be mapped to Zone 12.
!
Transmitter 410078:1, point 3 will be mapped to Zone 13.
The keypad will now display Zone 13, the last zone enrolled.
Example 2.
A 2-point transmitter has the RF ID number
287613:1.
Map point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone “06”.
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that
one point has been programmed. (Transmitter 287613:1,
point 1 will be mapped to Zone 6).
5. Enter Zone “09”.
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad
will beep once to indicate that one point has been
programmed. (Transmitter 287613:1, point 2 is mapped to
Zone 9).
CHANGING OR CANCELING A CODE:
To change
any code, merely program over the existing code as
described above and press
U
to save. Similarly, to
cancel a code, blank out each number of the code
and press
U
to save.
Note:
Duplicate User Codes are
not allowed; therefore a duplicate Code entered in the
LCD Window will erase when
U
is pressed.
