mycom 170J Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 209

background image

2205B0JE-DA-J-N_2014.05.

1 Safety

Screw Compressor J-series

1.4 Safety Devices

1-10

1.4 Safety

Devices

For safe use and protection of the compressor, make sure to attach safety devices to the compressor
that comply with the regulations and the following descriptions.

Safety devices must be properly and periodically maintained and inspected. It is important to include
maintenance and inspection of safety devices in the periodical maintenance/inspection schedule. Make
sure to provide users of the compressor with necessary information on types, attachment positions,
functions, inspection method of the safety devices.



Check the safety devices after turning on the power and before operation of the
compressor. If they do not operate normally, immediately take measures to
replace them.

1.4.1 Emergency Stop Button



Overview/Function/Purpose

The emergency stop buttons are used to stop the compressor operation immediately if an
emergency occurs to the compressor.



Installation

Locations

The emergency stop buttons should be installed in the controller on the compressor and in the
operating control room



Stop/Reset

Methods

To activate and reset the emergency stop buttons, refer to the unit instruction manual.



Inspection

Method/Cycle

The emergency stop buttons must be tested before a test run as well as periodically. For details
about the inspection procedure and inspection cycle of the emergency stop buttons, refer to the
unit instruction manual.

1.4.2 Breakers for the Main Motor Power and Control Power

(with Lockout/Tagout Devices)



Overview/Function/Purpose

Turn off the main motor and control power, and if there are any possibilities of danger during work
(especially during cleaning, maintenance, inspection, or troubleshooting), lockout/tagout devices
must be set up for breakers of the main motor and control powers to prevent injury to workers in
case the power is turned on accidentally during work.



Methods of Performing and Releasing Lockout/Tagout

In accordance with the regulations created by Occupational Safety & Health Administration
(OSHA) and other authorities, make sure to clearly indicate methods of performing and releasing
lockout/tagout and provide users of this compressor with the necessary information.



Inspection

Method/Cycle

For inspection procedures and the inspection cycle of the lockout/tagout devices, refer to the unit
instruction manual.

«
...
18
19
20
21
22
...
»

Содержание 170J


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 170J

Maneurop NTZ Series

Бренд: Danfoss Страницы: 28

Бренд: Xstream Страницы: 40

Бренд: King Canada Страницы: 3

Бренд: Campbell Hausfeld Страницы: 57

Бренд: DS Produkte Страницы: 4

Бренд: Johnson Controls Страницы: 64

Бренд: DV Systems Страницы: 20

Бренд: Nuvair Страницы: 40

Бренд: Bostitch Страницы: 2

Бренд: Champion Страницы: 36

Бренд: SereneLife Страницы: 5

Бренд: Fini Страницы: 14

SFX-09 Double Back

Бренд: Duncan Страницы: 2

JUN-AIR 120R-40B

Бренд: Gast Страницы: 19

Бренд: Gardner Denver Страницы: 84

ETERNITY CMP 2408

Бренд: Gecko Страницы: 14

Бренд: Omnitronic Страницы: 30

Бренд: Danfoss Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды