mycom 170J Скачать руководство пользователя страница 150

Страница: 150 / 209

2205B0JE-DA-J-N_2014.05.

6 Troubleshooting

Screw Compressor J-series

6-1

6 Troubleshooting

Table 6-1 Troubleshooting

Trouble

Direct causes

Factors

Actions

01 Compressor

not starting

Power source is off.

Most cases are due
to

neglect to turn

power source on
after inspection.

Prevent by checking using a check
sheet, and by pointing and calling.

Main motor
malfunction

Most cases are due
to overload
protection circuit.

Refer to the motor instruction
manual as well for other causes and
actions.

Capacity control of
0% undetected by
unloader indicator

Malfunction of
micro-switch

Replace micro-switch.

Capacity control
hydraulic circuit
defect

Maladjustment of oil
controller valve
(decreased too
much)

Readjust.

Leak or clogging in
pipes and solenoid
valves

Remove factors. Check oil
contamination level and replace
pipes and solenoid valves.

Unconfirmed
hydraulic pressure

Malfunction in hy-
draulic pressure
protection device,
pressure sensor,
relays, etc.

Identify malfunctioning devices,
examine their causes, and take
measures.

Then, replace malfunctioning
devices.

Clogging in
connecting pipes

Remove clogging. Check oil
contamination level and replace oil
as necessary.

Unconfirmed
cooling water
circulation

Malfunction in
devices such as
cooling water
pumps and related
circuits

Identify malfunctioning devices,
examine their causes, and take
measures.

Then, replace malfunctioning
devices.

Clogging in circula-
tion routes

Remove clogging.

Malfunction in mag-
nets, relays, etc., in
compressor start
circuit

Aging degradation

Replace with new devices.

Bad installation
environment

Replace ventilation fans, etc, if
malfunctioning.

Improve temperature, humidity, and
ventilation for installation site.

Compressor
stops imme-
diately after
startup.

Low pressure
protection circuit
activated

Insufficient refriger-
ant circulation
volume



Insufficient refrig-

erant amount



Insufficient refrig-

erant supply



Heat exchange

failure at heat
exchanger

For insufficient refrigerant amount,
check for and stop leak, and then
replenish refrigerant.

* Be aware of moisture

contamination in the system.

For insufficient supply, inspect
expansion valves and supplying
strainers, and then take necessary
measures.

Also, inspect devices and
parameters (setting values) for
expansion value aperture
adjustment device, and then take
necessary measures.

Содержание 170J


















































































































































































































Результаты поиска

Содержание 170J

Отзывы:

Похожие инструкции для 170J

Бренды по названию

Популярные бренды

mycom 170J, Инструкция по эксплуатации

Результаты поиска

Содержание 170J

Отзывы:

Похожие инструкции для 170J

Бренды по названию

Популярные бренды