mycom 170J Скачать руководство пользователя страница 14

Страница: 14 / 209

2205B0JE-DA-J-N_2014.05.

1 Safety

Screw Compressor J-series

1.2 Warnings

1-4

1.2 Warnings

To alert workers about possible dangers, the following two measures are always provided with the
compressor.



Warnings described in this manual



Safety labels affixed on the compressor

1.2.1 Types and Meanings of Warnings

This manual includes the following four types of warnings to be used for hazards during operation or
maintenance of the compressor.

Neglecting such warnings may cause accidents, resulting in personal injury or even death. Also, the
compressor or its auxiliary equipment may be heavily damaged. Therefore, be sure to always observe
the instructions of the warnings.

Table 1-1 Types and Meanings of Warnings in this manual

Warning Type

Meaning

Indicates an imminently hazardous situation which, if not avoided, will result in
serious injury or death.

Indicates a potential hazardous situation which, if not avoided, could result in serious
injury or death.

Indicates a potential hazardous situation which, if not avoided, may result in minor or
moderate injury.

Indicates a potentially hazardous situation which, if not avoided, may result in
property damage.

1.2.2 Safety

labels

The following shows the types of safety labels and their positions affixed on the compressor.

Always follow the warnings instructed on the safety label affixed on the compressor.



Be sure to follow the instructions of the safety labels. Otherwise, danger
resulting in personal injury, death, or property damage may arise.



Do not smear, cover, or peel off the safety labels.



If the safety labels are damaged or missing, purchase and affix new labels to their
proper positions according to this manual.



Inform our service centers of the product name and safety label number when placing a

purchase order for safety labels.

Содержание 170J


















































































































































































































Результаты поиска

Содержание 170J

Отзывы:

Похожие инструкции для 170J

Бренды по названию

Популярные бренды

mycom 170J, Инструкция по эксплуатации

Результаты поиска

Содержание 170J

Отзывы:

Похожие инструкции для 170J

Бренды по названию

Популярные бренды