mycom 170J Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 209

background image

2205B0JE-DA-J-N_2014.05.

5 Maintenance and Inspection

Screw Compressor J-series

5.4 Disassembly and Assembly of the Compressor

5-63

5.4.19.1 Common Precautions for Removal/Installation



Male rotor and female rotor

Weight of rotor alone (kg)

170JS 170JM 170JL

220JS

220JM

220JL

280JS 280JM 280JL

M

rotor 37 44 52 88 104 124 194 228 272

F

rotor

19 23 28 46 55 67 101

121

148



If lifted inappropriately, it may cause injuries. When lifting the male rotor or
female rotor use the lifting equipment, and make sure to adopt an appropriate
method such as using lifting slings.



If the lifting equipment and lifting slings in use do not have sufficient loading
capacity, the male rotor or female rotor may fall causing injuries and damage to
the compressor. Before starting the lifting work, always check that the lifting
equipment and lifting slings have sufficient loading capacity. Do not allow
anyone to be under the lifted male rotor or female rotor.



Do not damage the rotor, the casing, or the bearing when pulling out /installing
the rotors. Suspend the rotors and pull them out horizontally.

5.4.19.2 Precautions for Removal



Unloader slide valve assembly and Vi slide valve assembly

Weight of Unloader slide valve assembly (kg)

170JS 170JM

170JL

220JS

220JM

220JL

280JS 280JM 280JL

Unloader slide
valve

10 12 13 22 24 27 47 52 59

Slide valve, Vi

7

7.5

7.8

12.2

12.7

13.3

26

27

29



If lifted inappropriately, it may cause injuries.
If it is difficult to lift them by hand, use appropriate lifting equipment.

«
...
135
136
137
138
139
...
»

Содержание 170J


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 170J

Бренд: York Страницы: 4

Бренд: easymaxx Страницы: 52

Бренд: Gardner Denver Страницы: 58

TH-AC 200/24 OF

Бренд: EINHELL Страницы: 148

Бренд: Quipall Страницы: 24

Бренд: Coldex Страницы: 7

Бренд: Parkside Страницы: 86

Бренд: Parkside Страницы: 149

Бренд: Jet Страницы: 22

Portable Electric/Gas Compressor

Бренд: Eagle Страницы: 32

10020HdCAdC-22060

Бренд: California Air Tools Страницы: 17

Бренд: HSS Hire Страницы: 2

Бренд: HSS Hire Страницы: 2

Бренд: ASTA Страницы: 37

Бренд: Atlas Copco Страницы: 136

Бренд: Quincy Compressor Страницы: 92

Бренд: HART Страницы: 36

Central Pneumatic 4077

Бренд: Harbor Freight Tools Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды