mycom 170J Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 209

background image

2205B0JE-DA-J-N_2014.05.

7 Related Documents

Screw Compressor J-series

7.1 Development View and Configuration Table of the Parts

7-7

Part

No.

Part name

170J

Type, etc.

Part code No.

Quantity/unit

Standard

Explosion

proof for

Propane

S

M

L

732-C Plug

R1/8

NF06-004

1

732-D Plug

R1/8

NF06-004

1

733-A Plug

R1/8

NF06-004

1

733-B Plug

R1/8

NF06-004

1

734

Inner cover, balance piston cover

CS73400-J170

2

736 Partition

plate,

suction cover

CS73600-J170

1

744 O-ring

JIS

B2401

G55

PAH81-055

PC12-055 1

745 Rivet

3

dia.×6

4

235-1

Motor spacer

For NEMA 44*D

CS23502-J170NEMA44

1

Motor spacer

For NEMA 50*D

CS23502-J170NEMA50

Motor spacer

For IEC FF-500

CS23502-J170IEC50

Motor spacer

For IEC FF-600

CS23502-J170IEC60

235-2 Plate, motor spacer

CS23510-J170

2

235-3 Hexagon socket head cap screw

M6×15

NB35406-015

8

739

Hexagon socket head cap screw

M16×60

NB35416-060

8

740 Parallel

pin

13 dia.×65 with
female thread

NE2313-065A 2

●

As for the part code of the O-ring, the material of the standard specification is HNBR

and the material of the explosion-proof for propane specification is FKM.
For O-rings material other than HNBR or FKM, the part code No. are differ depending
on the material.
For customers using O-rings other than the standard material, contact
before purchasing the O-ring.



The abolition part and so on

The attendant explanation of the abolition part which is shown by the double strikethrough in table
7-1 is as the following table 7-1b

As for the design modification notification (follow-up), refer to 7.4 "Design Modification Notification
(follow-up) " in this chapter.

Table 7-1b

Part

No.

Part Name

Design Modification

Notification (first)

Remarks

Registration

No.

Issue

Date.

34-2 Spring

pin

664-055 2012.04.09

Design modification notification
(follow-up) No.C0956-02

35-1 O-ring

664-056 2012.04.09

36

Balance piston hausing

44-1

Thrust bearing gland spacer, M

664-054 2012.03.29

Design modification notification
(follow-up) No.C0957-00

44-2

Thrust bearing gland spacer, F

720

Vi position sensor support

With the explosion proof
compressors addition, these shift
to the exclusive instruction
manual as No. 794 Vi position
sensor assembly.

721 Potentiometer

722

Hexagon socket head cap screw

724

Vi position sensor box

727 I

plug

664-069 2013.10.31

729 Spring

pin

664-054 2012.03.29

Design modification notification
(follow-up) No.C0957-00

«
...
165
166
167
168
169
...
»

Содержание 170J


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 170J

Бренд: Campbell Hausfeld Страницы: 60

Бренд: Danfoss Страницы: 38

Бренд: Vmac Страницы: 64

Quick Flow 3-in-1 Air Compressor

Бренд: Wagan Страницы: 8

Бренд: Rolair Страницы: 47

Бренд: XTline Страницы: 71

Бренд: DeVillbiss Air Power Company Страницы: 24

Бренд: GEA Страницы: 32

Бренд: Sundyne Страницы: 82

In Touch HAX4/465-4

Бренд: GEA Bock Страницы: 32

Бренд: GEA Страницы: 26

Бренд: Heavy Duty Power Systems Страницы: 9

Fullmotion CF10C

Бренд: Embraco Страницы: 48

Бренд: Emax Страницы: 14

Бренд: AVANT Страницы: 47

Бренд: Devair Страницы: 24

Бренд: Oko Страницы: 4

Бренд: Champion Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды