mycom 170J Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 209

background image

2205B0JE-DA-J-N_2014.05.

5 Maintenance and Inspection

Screw Compressor J-series

5.4 Disassembly and Assembly of the Compressor

5-26

5.4.7.1 Common Precautions for Removal/Installation



Retaining ring E type/Vi position sensor rod



The Retaining ring E type may jump out, causing injuries. Make sure to use a
Retaining ring E type removing/attaching tool of suitable size and wear protective
tools such as protective goggles.



Because the Vi position sensor assembly uses a spring, the Vi position sensor rod
may jump out and cause injuries. During and after retaining ring removal, do not
direct the Vi position sensor assembly toward anyone.

5.4.7.2 Precautions for Removal



Sensor box lid



The sensor box lid mounting bolts are structured so that they do not drop off from the lid.



Vi position sensor assembly

1.

To remove the Vi position sensor rod housing, turn the Vi position sensor rod plug (No.715)
clockwise using a wrench.

5.4.7.3 Precautions for Installation



O-ring

1.

Make sure that all necessary O-rings are attached. (In particular, part No. 714)



Vi position sensor rod housing gland

1.

Install the Vi position sensor rod housing
gland of the groove facing down.

«
...
98
99
100
101
102
...
»

Содержание 170J


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 170J

Бренд: Brooks Страницы: 56

Бренд: Powermate Страницы: 24

DC850R Pro Series

Бренд: paasche Страницы: 2

Бренд: Ironton Страницы: 20

Бренд: Motomaster Страницы: 18

Бренд: Parkside Страницы: 86

Бренд: Parkside Страницы: 149

Бренд: Sakura Страницы: 10

Бренд: FScurtis Страницы: 78

Бренд: WilTec Страницы: 9

Бренд: Manta Страницы: 20

Бренд: Eastwood Страницы: 12

Бренд: Ingersoll-Rand Страницы: 44

Бренд: Ingersoll-Rand Страницы: 57

Бренд: Ingersoll-Rand Страницы: 98

Reciprocating Air Compressors

Бренд: Jenny Страницы: 53

Бренд: Gis Страницы: 56

Бренд: Mangar Health Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды