manualshive.com logo in svg

MTU 12 V 4000 Lx4, Руководство по эксплуатации

Поделиться
Скачать
MTU 12 V 4000 Lx4 Скачать руководство пользователя страница 95

1.4520.673 – MIC5 E2 Tr3 polarity detection fail

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

Polarity of trigger 3 (B13.2)
could not be detected.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.674 – MIC5 E2 Tr3 wrong polarity

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

Trigger 3 (B13.2) has wrong
polarity.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.675 – MIC5 E2 Tr3 no index mark detected

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

Index mark of trigger 3 (B13.2)
was not detected.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.676 – MIC5 E2 Tr3 wrong n of trigg events

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

The number of trigger 3 (B13.2)
events is not correct.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.677 – MIC5 E2 Tr3 signal missing

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

An expected signal from trigger
3 (B13.2) was missing

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.678 – MIC5 E2 Tr3 signal faulty

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

An unexpected signal from
trigger 3 (B13.2) was detected.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.679 – MIC5 E2 Tr3 index mark not detected

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

The index mark of trigger 3
(B13.2) was not detected during
operation.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

MS15027/00E 2013-10

| Troubleshooting | 95

TIM-ID: 0000044566 - 001

Содержание 12 V 4000 Lx4








































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды