MTU 12 V 4000 Lx4 Скачать руководство пользователя страница 144

Страница: 144 / 199

932 – AL MIC5 Yellow

Yellow alarm.
Associated parameter 1.4520.933

Cause

Corrective action

An internal combined alarm in
the ignition system was
detected.

Precise error name is sent to the genset control via CAN bus.

933 – AL MIC5 Red

Red alarm.
Associated parameter 1.4520.936

Cause

Corrective action

An internal combined alarm in
the ignition system was
detected.

Precise error name is sent to the genset control via CAN bus.

934 – AL MIC5 Comm Lost

Red alarm.
Associated parameter 1.4520.939

Cause

Corrective action

CAN bus communication to
ignition system faulty.

1. Check cabling.
2. Check power supply.
3. Restart ECU, EMU & knock control.
4. Check settings using device-specific dialog software (in device).

948 – AL ESI activated

Red alarm.
Associated parameter 2.8006.044

Cause

Corrective action

Emergency stop input is
activated.

1. Rectify the fault causing the alarm.
2. Check cabling.

972 – AL MIC5 Signature difference

Red alarm.
Associated parameter 1.450.969

Cause

Corrective action

The ignition system has not
taken on the configuration from
the engine governor.

1. ECU restart
2. Check configuration in the ECU

144 | Troubleshooting | MS15027/00E 2013-10

TIM-ID: 0000044567 - 001

Содержание 12 V 4000 Lx4








































































































































































































Результаты поиска

Содержание 12 V 4000 Lx4

Отзывы:

Бренды по названию

Популярные бренды

MTU 12 V 4000 Lx4, Руководство по эксплуатации

Результаты поиска

Содержание 12 V 4000 Lx4

Отзывы:

Бренды по названию

Популярные бренды