manualshive.com logo in svg

MTU 12 V 4000 Lx4, Руководство по эксплуатации

Поделиться
Скачать
MTU 12 V 4000 Lx4 Скачать руководство пользователя страница 93

1.4520.660 – MIC5 E2 Tr2 no signal detected

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

No signal from trigger 2 (B75).

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.661 – MIC5 E2 Tr2 polarity detection fail

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

Polarity of trigger 2 (B75) could
not be detected.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.662 – MIC5 E2 Tr2 wrong polarity

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

Trigger 2 (B75) has wrong
polarity.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.663 – MIC5 E2 Tr2 no index mark detected

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

Index mark of trigger 2 (B75)
was not detected.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.664 – MIC5 E2 Tr2 wrong n of trigg events

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

The number of trigger 2 (B75)
events is not correct.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.665 – MIC5 E2 Tr2 signal missing

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

An expected signal from trigger
2 (B75) was missing

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

1.4520.666 – MIC5 E2 Tr2 signal faulty

Yellow alarm. Initiated by MIC5.

Cause

Corrective action

An unexpected signal from
trigger 2 (B75) was detected.

u

Check sensor, sensor spacing, cabling, settings in data record
and timing wheel. Replace sensor if required.

MS15027/00E 2013-10

| Troubleshooting | 93

TIM-ID: 0000044566 - 001

Содержание 12 V 4000 Lx4








































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды