manualshive.com logo in svg

MTU 12 V 4000 Lx4, Руководство по эксплуатации

Поделиться
Скачать
MTU 12 V 4000 Lx4 Скачать руководство пользователя страница 129

511  –  HIHI P-Charge Mix A

Red alarm. Engine stop.
Associated parameter 2.0181.932

Cause

Corrective action

Mixture pressure on A side too
high (limit value 2).

1. Check emissions.
2. Check ignition timing (→ Page 160).
3. Check exhaust back pressure.
4. Check valve clearance (→ Page 165).
5. Check throttle.
6. Check mixture coolant system.

512  –  HIHI P-Charge Mix B

Red alarm. Engine stop.
Associated parameter 2.0182.932

Cause

Corrective action

Mixture pressure on B side too
high (limit value 2).

1. Check emissions.
2. Check ignition timing (→ Page 160).
3. Check exhaust back pressure.
4. Check valve clearance (→ Page 165).
5. Check throttle.
6. Check mixture coolant system.

513  –  SD P-Coolant Diff

Red alarm.
Associated parameter 1.8004.610

Cause

Corrective action

Coolant differential pressure
sensor defective, short circuit or
wire break.

u

Check sensors and cabling (B16.1, B16.3), replace if necessary.
Fault is rectified following engine restart.

515 –  AL Starter Not Engaged

Yellow alarm.
Associated parameter 1.8004.123

Cause

Corrective action

Gas temperature sensor
defective, short circuit or wire
break.

1. Not available in all engine versions (optional).
2. Check sensor and cabling (B38), replace as necessary.

517  –  SD P-Charge Mix before Throttle

Red alarm.
Associated parameter 1.8004.631

Cause

Corrective action

Mixture pressure sensor before
throttle defective, short circuit
or wire break.

u

Check sensor and cabling (B79.23), replace if necessary. Fault
is rectified following engine restart.

MS15027/00E 2013-10

| Troubleshooting | 129

TIM-ID: 0000044567 - 001

Содержание 12 V 4000 Lx4








































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды