manualshive.com logo in svg

MTU 12 V 4000 Lx4, Руководство по эксплуатации

Поделиться
Скачать
MTU 12 V 4000 Lx4 Скачать руководство пользователя страница 131

554  –  AL Ignition Fault

Red alarm.
Associated parameter 2.1090.122

Cause

Corrective action

Ignition failure. Alarm is
activated if the feedback signal
from ignition system is not
received within a specified time-
out period. Either the ignition
could not be activated, the time-
out period is set too short, or
communication is faulty.

1. Check ignition system.
2. Check cabling.

556  –  AL GasValve Fault

Red alarm.
Associated parameter 2.1090.124

Cause

Corrective action

Gas supply solenoid valve faulty.
Alarm is activated when
problems with the gas supply
solenoid valves occur. Either the
gas supply solenoid valves are
faulty, the time-out period is set
too short, or communication is
faulty.

1. Check gas train.
2. Check cabling.

557  –  AL speed drop fault

Red alarm. Engine stop.
Associated parameter 2.1090.126

Cause

Corrective action

Speed drop. Alarm is activated if
engine speed drops during
starting sequence.

u

Check gas train.

559  –  AL mixture throttle A fault

Red alarm. Engine stop.
Associated parameter 1.1450.010

Cause

Corrective action

A problem related to mixture
throttle on A side occurred.
Possible causes: Mixture throttle
defective, no power supply to
throttle, cabling of feedback
and/or position signal faulty.

u

Check mixture throttle on A side and cabling. Replace mixture
throttle on A side if necessary.

MS15027/00E 2013-10

| Troubleshooting | 131

TIM-ID: 0000044567 - 001

Содержание 12 V 4000 Lx4








































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды