MTU 12 V 4000 Lx4 Скачать руководство пользователя страница 36

Страница: 36 / 199

3.2 Putting the engine into operation after extended out-of-service

periods (>3 months)

Preconditions

☑

Engine is stopped and starting disabled.

☑

MTU Fluids and Lubricants Specifications (A001061/..) are available.

Putting the engine into operation after extended out-of-service-periods (>3
months)

Item

Measure

Engine

Depreserve (→ MTU Preservation and Represervation Specifications
A001070/..).

Engine

Bar engine manually (→ Page 147).

Valve gear

Standstill ≥ 6 months: Lubricate valve gear (→ Page 164).

Lube oil system

Check engine oil level (→ Page 173);
Check oil level in oil storage tank (→ Page 173).

Coolant circuit

Standstill > 1 year: Change engine coolant (→ Page 178);
Change mixture coolant (→ Page 183)

Coolant circuit

Check engine coolant level (→ Page 177);
Check mixture coolant level (→ Page 182)

Engine cabling

Check plug-in connections (→ Page 186).

Gas supply

The gas shut-off valves with control solenoids are not included in the scope
of supply of the engine. The components are controlled by the engine elec-
tronics.

Engine management system Check for fault messages.
Starting system

Check power supply to electric starter.

36 | Operation | MS15027/00E 2013-10

TIM-ID: 0000029117 - 002

Содержание 12 V 4000 Lx4








































































































































































































Результаты поиска

Содержание 12 V 4000 Lx4

Отзывы:

Бренды по названию

Популярные бренды

MTU 12 V 4000 Lx4, Руководство по эксплуатации

Результаты поиска

Содержание 12 V 4000 Lx4

Отзывы:

Бренды по названию

Популярные бренды