manualshive.com logo in svg

MR TAPCON 230 AVT, Руководство по эксплуатации

Поделиться
Скачать
MR TAPCON 230 AVT Скачать руководство пользователя страница 144

11 Fault elimination

Maschinenfabrik Reinhausen GmbH 2021

144

7817454/02 EN

TAPCON

®

 230 Expert

Characteristics/details

Cause

Remedy

Problem with master/follower par-
allel operation method:

▪ Master/follower switching char-

acteristics is "in synch".

Master and followers have differ-
ent tap positions.

Check tap position capture or check why the
tap-change operation has not been undertaken
(e.g. mechanical defect), then perform one of
the following steps:

▪ Manually correct the master's tap position.

▪ Restart master.

▪ Set master/follower switching characteristics

to "sequential".

▪ Change master device to follower and define

a different device as the master.

Problem with circulating reactive
current minimization parallel oper-
ation method.

Circulating reactive current can-
not be calculated.

Check wiring. Connect as shown in connection
diagram.

Circulating reactive current block-
ing limit exceeded.

Check configuration.

Table 53: Parallel operation faults

11.7 Tap position capture incorrect

Characteristics/detail

Cause

Remedy

Position indicator incorrect.

▪ Leading sign incorrect.

Incorrect wiring.

Check wiring.

Connect as shown in connection diagram.

Minimum value of the analog in-
put signal not configured cor-
rectly.

Check parameters.

Position indicator incorrect.

▪ Display fluctuates.

Interference.

Shield the line.

Increase distance from source of interference.

Lay interference lines separately.

Route signal in separate lines (filter, shielded
lines).

No position indicator.

▪ "- -" is displayed.

No measurement signal.

No L- for digital input.

Connect signal as shown in connection dia-
gram.

Check wiring.

Connect as shown in connection diagram.

No position indicator.

▪ "?" is displayed.

Bit combination (code) impermis-
sible.

Check wiring.

"Motor running" signal present.

Check the signal sequence.

Tap position capture over resistor
contact series faulty.

Faulty calibration.

Calibrate tap position capture over resistor con-
tact series.

Modified contact resistance val-
ues of the resistor contact series
(e.g. due to weather or age).

Calibrate tap position capture over resistor con-
tact series.

Table 54: Tap position capture

Содержание TAPCON 230 AVT







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды