MR TAPCON 230 AVT Скачать руководство пользователя страница 121

Страница: 121 / 166

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

121

7817454/02 EN

TAPCON

230 Expert

1. Go to

Settings > Parameters > On-load tap-changer regulator > Com-

pensation

2. Select the desired parameter.

3. Set the desired parameter.

4. Press the

Accept

button to save the modified parameter.

Voltage increase

You can use this parameter to set the current-dependent voltage increase
∆U.

Voltage limit value

You can use this parameter to define the maximum permissible voltage in-
crease to avoid excess voltage on the transformer.

9.3.3 Parallel operation

Parallel transformer operation is used to increase the throughput capacity or
short-circuit capacity at one location. The device provides you with specific
functions for regulating transformers.

Conditions for parallel

operation

Compliance with the following general conditions is required for operating
transformers in parallel:

▪ Identical rated voltages

▪ Transformer power ratio (< 3 : 1)

▪ Maximum deviation of short-circuit voltages (U

) for transformers con-

nected in parallel < 10%

▪ The same number of switching groups

▪ For parallel operation with CAN communication: Current transformers with

the same connection values must be used for all devices operating in par-
allel

9.3.3.1 Parallel operation methods

You can undertake parallel operation with various parallel operation meth-
ods.

Содержание TAPCON 230 AVT







































































































































































Результаты поиска

Содержание TAPCON 230 AVT

Отзывы:

Бренды по названию

Популярные бренды

MR TAPCON 230 AVT, Руководство по эксплуатации

Результаты поиска

Содержание TAPCON 230 AVT

Отзывы:

Бренды по названию

Популярные бренды