manualshive.com logo in svg

MR TAPCON 230 AVT, Руководство по эксплуатации

Поделиться
Скачать
MR TAPCON 230 AVT Скачать руководство пользователя страница 137

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

137

7817454/02 EN

TAPCON

®

 230 Expert

V

s

1

2

1

Figure 60: Switching pulse time and switching pulse pause

1 Switching pulse time

2 Switching pulse pause

Switching pulse time

You can use this parameter to set the maximum duration of the switching
pulse. The switching pulse resets after the switching pulse time has elapsed
or if the device receives the 

Motor running

 signal beforehand or the tap posi-

tion is changed.

Switching pulse pause

You can use this parameter to set the switching pulse pause between 2
switching pulses. The device can only issue another switching pulse once
the switching pulse pause has elapsed.

9.5.1.2 Setting motor runtime monitoring

The motor-drive unit's runtime  can be monitored by the device. This function
is used to identify motor-drive unit malfunctions during the tap-change oper-
ation and to trigger any actions needed.

Behavior

The motor-drive unit issues the 

Motor-drive unit running

 signal during the

tap-change operation. This signal is present until the tap-change operation is
complete. The device compares the duration of this signal with the set motor
runtime. If the set motor runtime is exceeded, the device triggers the follow-
ing actions:

1.

Motor runtime exceeded

 event.

2. Pulse signal via 

Trigger motor protective switch

 output relay

Note that motor-drive units with pass-through positions or motor-drive units
without stepped switching behavior will run for longer under certain circum-
stances. Set a longer motor runtime for such units.

1. Go to 

Settings > Parameters > Motor and control cabinet > Motor

control

.

2. Select the desired parameter.

Содержание TAPCON 230 AVT







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды