MR OILTAP R Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 206

MR OILTAP R Скачать руководство пользователя страница 79

5 Mounting

Maschinenfabrik Reinhausen GmbH 2015

79

4427410/00 EN

OILTAP® R

Carrying out transformer ratio test with TAPMOTION® TD test drive

NOTICE

Damage to the on-load tap-changer!

Performing too many operations without complete oil filling will damage the
on-load tap-changer!
► Do not perform more than 250 tap-change operations on the on-load

tap-changer without oil before drying.

► Before first actuating the on-load tap-changer after drying the trans-

former, the tap selector and change-over selector (if present) must be
completely immersed in transformer oil and the oil compartment must
be completely filled with oil.

After the transformer ratio test, open the kerosene drain plug in the oil com-
partment if the on-load tap-changer is to be dried with kerosene in the trans-
former tank. After drying, the diverter switch insert must be removed, the
kerosene drain plug in the oil compartment closed and the diverter switch
insert refitted.

In order to run the transformer ratio test, we recommend using the
TAPMOTION® TD test drive. The precise process is described in the test
drive operating instructions.

Carrying out the transformer ratio test manually

NOTICE

Damage to the on-load tap-changer!

Performing too many operations without complete oil filling will damage the
on-load tap-changer!
► Do not perform more than 250 tap-change operations on the on-load

tap-changer without oil before drying.

► Before first actuating the on-load tap-changer after drying the trans-

former, the tap selector and change-over selector (if present) must be
completely immersed in transformer oil and the oil compartment must
be completely filled with oil.

To actuate the drive shaft of the upper gear unit of the on-load tap-changer
head, you can use a short tube (diameter 25 mm) with screwed-in coupling
bolt (diameter 12 mm) with a hand wheel or crank.

5.3.3.1

5.3.3.2

«
...
77
78
79
80
81
...
»

Содержание OILTAP R















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды