manualshive.com logo in svg

MR OILTAP R, Инструкции по установке и вводу в эксплуатацию

Поделиться
Скачать
MR OILTAP R Скачать руководство пользователя страница 7

1 Introduction

Maschinenfabrik Reinhausen GmbH 2015

7

4427410/00 EN

OILTAP® R

Introduction

This technical file contains detailed descriptions of the safe and proper in-
stallation, connection, and commissioning of the product.

It also includes safety instructions and general information about the prod-
uct.

Information about operation can be found in the operating instructions.

This technical file is intended solely for specially trained and authorized per-
sonnel.

Validity

The document supplied with the product is always the valid version. This
technical file is configured for the specific order and applies to the following
products, the serial numbers of which can be found on the delivery docu-
ments:
▪

OILTAP® R type on-load tap-changer

▪

RS protective relay

▪

Pressure monitoring device DW 2000 (optional)

▪

Drive shaft

Manufacturer

The product is manufactured by:

Maschinenfabrik Reinhausen GmbH

Falkensteinstraße 8
93059 Regensburg, Germany
Tel.: (+49) 9 41/40 90-0
Fax: (+49) 9 41/40 90-7001
E-mail: [email protected]

Further information on the product and copies of this technical file are avail-
able from this address if required.

Subject to change without notice

The information contained in this technical file comprises the technical speci-
fications approved at the time of printing. Significant modifications will be in-
cluded in a new edition of the technical file.

The document number and version number of this technical file are shown in
the footer.

Completeness

This technical file is incomplete without the supporting documentation.

1

1.1

1.2

1.3

1.4

Содержание OILTAP R















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды